Mitsubishi Relay Output Module AJ65SBTB2N-8R

Mitsubishi Relay Output Module AJ65SBTB2N-8R

Mitsubishi Relay Output Module AJ65SBTB2N-8R Product Name: Mitsubishi Relay Output Module Model and Specification: AJ65SBTB2N-8R Output 8 Point: 24VDC/240VAC (2A). Relay output. 2-wire. Terminal type.

Overview of Mitsubishi CC-LINK module AJ65SBTB2N-8R:

8-point relay output DC 24 V, AC 240 V, 2A, dual wire type

Output points: Relay output 8 points, dual wire type

Rated voltage and current switch: DC 24V/AC 240 2A

Mitsubishi CC-LINK module AJ65SBTB2N-8R Other energy specifications:

***Small load switch: DC 5V 1mA

Switching voltage: AC 264V DC 125V

Switching frequency: 3600 times/hour

Alarm output method: 8 points (terminal block shape with 2 wires)

Response time: 12ms

Insulation and withstand voltage:

AC external terminal between one-time and earth: AC 2830 Vrms/3 cycles (altitude 2000 meters)

DC external terminal between one-time and earth: AC 500 V for 1 minute

External circuit connection method:

Communication Department, Power Department: 7-point 2 terminal blocks (M3 screws)

Input and output power supply, input and output part: 18 points directly attached terminal block (M3 screw)

External dimensions H * W * D mm: 50 * 118 * 40

Weight: 0.25Kg

Mitsubishi CC-LINK module AJ65SBTB2N-8R features:

The wiring operation is simple:

The use of terminal block screws for tensioning greatly reduces the wiring process.

Can connect 64 remote I/O units:

The main office of the CC Link system can connect to one remote I/O unit, with 64 units. In addition, one remote I/O unit is approximately 32 o'clock, so the link score can be set before 2048 o'clock.

Exchange of CC Link system stop units:

The cable connection terminal block of the CC Link system has two terminal blocks. By using them, the CC Link system stops the possibility of unit exchange.

Machine installation may directly affect:

Compared to finger protection on the upper part of the terminal block, the remote I/O unit of the terminal block type is also mechanically installed and used directly due to the lack of contact with the charging department personnel.

The unit can be installed in 6 directions:

The small remote I/O unit is installed and used in 6 directions. In addition, the installation of DIN rails may also be a limiting factor for some installation directions.

1. Mitsubishi full series PLC, frequency converter, human-machine interface, servo system.

2. Xinjie PLC, frequency converter, human-machine interface and servo system.

3. Delta PLC, frequency converter, human-machine interface and servo system.

4. Wellington human-machine interface and Hytec human-machine interface.

Mitsubishi servo motor HG-JR15K1MB;

Mitsubishi servo motor HG-JR11K1MB;

Mitsubishi servo drive MR-J4-11KA

Mitsubishi servo drive MR-J4-11KB

Mitsubishi servo drive HG-KR-23J with oil seal

Mitsubishi servo store HG-KR053

Mitsubishi servo motor HG-KR73BJ with oil seal

Mitsubishi servo motor HG-SR102BJ with oil seal

Mitsubishi MR-J4-15KB servo driver

Mitsubishi PLC (programmable controller) A, R, Q, L, CC-LNK, FX3SA, FX3G, FX3G, FX3U, FX5U and other series;

Mitsubishi frequency converter A840, E840, F840, E740, D740, D720 series; Mitsubishi touch screen GT2000 series; Mitsubishi servo motor JE, J4 series.

Mitsubishi programmable controller: FX3GA, FX3GE, FX3G, FX3U, FX3UC, FX2NC, A, Q, CC-LINK remote module and other series

Mitsubishi variable frequency governor: FR-L700, FR-A700/500, F700/500, E700/500, D700/500, S500 and other series;

Man-machine interface: GOT2000, GOT16, GOT15, GOT12, GOT11, GOT10, A900GOT, F900GOT and other series;

AC servo system: MR-J4, MR-JE, MR-J3, MR-J2S, MR-E, MR-ES and other series;

Tension control system: LE-40MTA (B), LD-FX, LD-50PAU and other series:

Low-voltage electrical appliances: S-N, TH-N, etc.