Mitsubishi PLC module AJ65SBTB1-32DT3

Mitsubishi PLC module AJ65SBTB1-32DT2

Basic parameters of Mitsubishi AJ65SBTB1-32DT2: 16 points, input/transistor output (drain type), high-speed/LOW LEAK

Weight: 0.25kg

[AJ65SBTB1-32DT2 Input Specification] Input points: 16

Insulation method: optocoupler insulation

Rated input voltage: DC24V

Rated input current: approximately 7mA

Voltage range: DC19.2-26.4V (fluctuation rate within 5%)

Simultaneously input points:***

ON voltage/ON current: above 14V/3.5mA

OFF voltage/OFF current: below 6V/below 1.7mA

Input resistance: approximately 3.3k Ω

Response time: below 1.5ms (at DC24V)

Input form: positive common terminal (leakage type)

[AJ65SBTB1-32DT2 Output Specification] Output Points: 16

Insulation method: optocoupler insulation

Rated load voltage: DC24V

Load voltage range: DC19.2-26.4V (fluctuation rate within 5%)

Load current: 0.5A/1 point 1.2A/1 common terminal

Inrush current: below 1.0A l0ms

Leakage current at OFF: below 0.1mA

Voltage drop during ON: below 0.3V (TYP) 0.5A below 0.6V

Output form: leakage type

Protection function: None

Response time: OFF ->ON: less than 0.5ms

ON ->OFF: below 1.5ms (resistive load)

External power supply for output part: Voltage: DC19.2-26.4V (fluctuation rate within 5%)/Current: Below 30mA (DC24V 1 common terminal), excluding external load current

Overcurrent suppressor: Zener diode

Common terminal method: 32 point 1 common terminal (terminal strip type 3-wire type)

Number of occupied stations: 1 station allocates 32 points (using 32 points)

I/O module power supply: voltage: DC20.4~26.4V (fluctuation rate within 5%)/current: below 60mA (DC24V, when all points are ON) without external load current

Noise intensity: With a DC type noise voltage of 500VP-P and a noise width of 1 μ s. The noise generated by a noise simulator with a noise frequency of 25-60Hz

Withstand voltage: AC500V between DC external terminal summary and ground for 1 minute

Insulation resistance: DC500V insulation resistance meter measures above 10 Ω between DC external terminals and ground

Protection level: IP2X

External connection method: communication part, I/O module power supply part: 7-point 2-segment terminal strip [transmission circuit, I/O module power supply, FG]/M3 * 5.2 tightening torque 59~88N · cm, suitable for inserting no more than 2 compression terminals

Input/output power supply section, input/output section: Install terminal blocks directly at 34 points (input/output power supply, I/O

1. Mitsubishi full series PLC, frequency converter, human-machine interface, servo system.

2. Xinjie PLC, frequency converter, human-machine interface and servo system.

3. Delta PLC, frequency converter, human-machine interface and servo system.

4. Wellington human-machine interface and Hytec human-machine interface.

Mitsubishi servo motor HG-JR15K1MB;

Mitsubishi servo motor HG-JR11K1MB;

Mitsubishi servo drive MR-J4-11KA

Mitsubishi servo drive MR-J4-11KB

Mitsubishi servo drive HG-KR-23J with oil seal

Mitsubishi servo store HG-KR053

Mitsubishi servo motor HG-KR73BJ with oil seal

Mitsubishi servo motor HG-SR102BJ with oil seal

Mitsubishi MR-J4-15KB servo driver

Mitsubishi PLC (programmable controller) A, R, Q, L, CC-LNK, FX3SA, FX3G, FX3G, FX3U, FX5U and other series;

Mitsubishi frequency converter A840, E840, F840, E740, D740, D720 series; Mitsubishi touch screen GT2000 series; Mitsubishi servo motor JE, J4 series.

Mitsubishi programmable controller: FX3GA, FX3GE, FX3G, FX3U, FX3UC, FX2NC, A, Q, CC-LINK remote module and other series

Mitsubishi variable frequency governor: FR-L700, FR-A700/500, F700/500, E700/500, D700/500, S500 and other series;

Man-machine interface: GOT2000, GOT16, GOT15, GOT12, GOT11, GOT10, A900GOT, F900GOT and other series;

AC servo system: MR-J4, MR-JE, MR-J3, MR-J2S, MR-E, MR-ES and other series;

Tension control system: LE-40MTA (B), LD-FX, LD-50PAU and other series:

Low-voltage electrical appliances: S-N, TH-N, etc.