Home > Products > line splice > Line splicing/GALVANIZED STEEL ARMOUR ROD
Line splicing/GALVANIZED STEEL ARMOUR ROD
- Any port in China
- T/T Credit Card PayPal
You May Like
Product Description
Line splicing
Application&Structure
Full tension preformed conductor splice follow the break connection, damage repair and so on, can replace the widely used hydraulic connecting pipes, burst pressure connecting tubes connecting methods.
Full tension preformed conductor splice is made from the inner section of tension continue, filling section, the outer section of three parts.
1)The inner rods Shall be used to follow steel core;
2)Filling rods shall be installed in the inner layer, guaranteeing installation of the same diameter and the diameter ACSR.
3)The outer line splicing is designed to follow basic agreement Traverse only slightly increased to compensate for the length of stripped of the aluminum wire.
Characteristics
1.The grip strength of full tension preformed conductor splice forces up to the rated breaking strength of strands, such as electrical conductivity than ACSR long.
2.Full tension preformed conductor splice can be restored ACSR Tension follow the breaking strength of 100% and 100% of the wire resistance.
Consideration
1.Whether or not the new and old wire, steel core and aluminum wire must be installed within the length of the article follow the surface thoroughly polished, bright and clean the surface after the coated surface quality immediately, and the conductive grease wire match, and then Start the installation.
2.When connecting the wire section of the mid-point and point alignment damaged during installation, the end lengh of full tension preformed conductor splice has been installed from end of the preformed armour rods or short preformed armour rods is not less than 150mm, only wire damage on the last point in the support points or damage point, we can continue with this article, and play follow the maintenance performance of the above article.
3.Full tension preformed conductor splice can only be used once.
GALVANIZED STEEL ARMOUR ROD For Steel cable, Strand
Art.no | Dia,Range(mm) | GB 1200-75 | Length(mm) | |||
ARAC 039-042 | 3.95 | 4.25 |
| 860 | ||
ARAC 046-048 | 4.60 | 4.85 |
| 910 | ||
ARAC 054-057 | 5.40 | 5.75 |
| 970 | ||
ARAC 059-062 | 5.95 | 6.20 |
| 1020 | ||
ARAC 062-065 | 6.21 | 6.58 | 25 | 1030 | ||
ARAC 073-078 | 7.37 | 7.82 | 35 | 1120 | ||
ARAC 088-094 | 8.81 | 9.47 | 50 | 1225 | ||
ARAC 105-110 | 10.52 | 11.07 | 70 | 1335 | ||
ARAC 124-132 | 12.47 | 13.23 | 95/100 | 1435 | ||
ARAC 139-146 | 13.91 | 14.60 |
| 1520 | ||
ARAC 146-152 | 14.61 | 15.20 |
| 1570 |
TOLERANCES: LENGTH:-10/+20mm. DIAMETER OF THE RODS: ±0.04mm
RAW MATERIAL :GALVANIZED STEEL
Be used for steel cable, strand
ISO 9001:2008
Package
Contact Us
- Nanjing Ocean-Runpower Electric Co., Ltd.
- Contact nameWilson Fang Chat Now
- Phone86-025-84717199
- AddressIndustrial Park, sanshan , Banqiao Street, Yuhuatai District Nanjing Jiangshu China, Nanjing, Jiangsu
Product Categories
Accessories | ADSS cable | armor rod | Dead end Grip |
electrified railways products | line splice | New Products | OPGW cable |
optical cable fittings | overhead line fittings | suspension set |
New Products
-
Reducing Splice
-
Open Wire Splice
-
Strand Splice
-
Overhead Shield Wire Repair Rods
-
Repair Rods for OPGW
-
Suspension clamp for OPGW cable/Preformed Fitting Suspension Clamp
-
Suspension clamp for OPGW cable
-
Suspension string for OPGW cable
-
Suspension clamp for OPGW cable
-
Preformed suspension clamp for OPGW cable
-
Preformed dead-end clamp for OPGW cable
-
Overhead line clamp
Popular Searches
- switchgear
- distribution board
- Zinc Oxide Varistor
- Lightning Rod
- spd
- surge protector
- surge arrester
- surge suppressor
- power surge
- lightning arrester
- zinc oxide lightning arresters
- Lightning Arrester Rod
- Lightning Rod Tower
- Polymer Surge Arrester
- electrical switchgear
- zinc oxide varistors
- power distribution unit
- pdu
- Power Supply Device
- distribution cabinet
- Metal Oxide Varistor
- cabinet pdu
- rack pdu
- power distribution cabinet
- Power Resistor
- High Voltage Resistor
- switchboard
- hv switchgear
- gas insulated switchgear
- ring main unit
Recommended Products
- Polyester Enclosure Fiberglass box IP65 waterproof GRP Cabinet distribution box
- AC LV Withdrawable Switchgear
- SF6 Fully Insulated Ring Main Unit
- Combined Busbar Hydraulic Turret-Type 3 in 1 Processing Machine with CE certified (EU standards) & ISO 9001
- Double Ended CNC Busbar Trunking Bending Machine
- Automatic Servo Turret CNC Three-table Busbar Processing Machine
- Open-Type Manual Control Hydraulic Turret-Type 3 in 1 Busbar Processing Machine-Heavy-Duty
- Open-Type Hydraulic Turret-Type 3 in 1 CNC busbar processing machine/303A,303B,303/503C,303/503D
- CNC Double Table 3 in 1 Turret-Type Busbar Processing Machine close type ISO 9001 BT-C303C/BT-C503C/BT-C803C
- Manual Control Hydraulic Turret-Type 3 in 1 Busbar processing Machine-Closed Type BT-M303C/BT-M503C
- Wholesales NSPV MLJ-01 connector Solar PV Panel Mini Junction Box
- 17.5 KV Full-enclosed Outdoor Epoxy Resin Casting and Double Pole Insulated Voltage Transformer
Find Similar Products By Category
- Electrical & Electronics > Power Supply & Distribution > Power Distribution Cabinet & Box
- Please Enter your Email Address
- Please enter the content for your inquiry.
We will find the most reliable suppliers for you according to your description.
Send Now-
Wilson Fang
Hi there! Welcome to my shop. Let me know if you have any questions.
Your message has exceeded the limit.

- Contact supplier for lowest price
- Customized Request
- Request Sample
- Request Free Catalogs
Your message has exceeded the limit.
-
Purchase Quantity
-
*Sourcing Details
Your inquiry content must be between 10 to 5000 characters.
-
*Email
Please enter Your valid email address.
-
Mobile