Home > Products > hot switch > TS0881-0601c tact switch suppliers
TS0881-0601c tact switch suppliers
US$ 0.001 - 0.1
/ Piece
1000 Pieces(Min. Order)
- ningbo or shanghai
- Credit Card
You May Like
Product Details
| Place of Origin | Zhejiang, China | Brand Name | omter | |
| Model Number | TS0881-0601c | Protection Level | DC12V 50mA | |
| Max. Current | - | Max. Voltage | AC250V for 1 minute |
Product Description
Specifications
1.small size suitable for high density mounting.2.Much thinner and lighter than conventional products.
tact switch
Item no.: TS0881-0601c
Detailed picture:
Drawing:
| APPROVAL SPECIFICATIONS: | |||||||||||||||||
| General characteristics: | |||||||||||||||||
| Application:This specification is applied to the requirements for TACTILE SWITCH (MECHANICAL CONTACT) | |||||||||||||||||
| Operating Temperature Range:-20°C~70°C(Normal humidity, normal air pressure) | |||||||||||||||||
| Storage Temperature Range:-30°C~80°C(Normal humidity, normal air pressure) | |||||||||||||||||
| Test Conditions Unless otherwise specified, tests and measurement shall be made in the following standard conditions: Normal temperature………………5°C~35°C Normal humidity…………………relative humidity 45%~85% Normal air pressure…………………86Kpa~106Kpa If any doubt arise from the judgment, tests shall be conducted at the following conditions: Temperature………………………20°C±2°C Relative humidity………………65%±5% Air pressure…………………………86KPa~106Kpa | |||||||||||||||||
| Detailed specification: | |||||||||||||||||
| Appearance: There should be no defects that affect the serviceability of product. | |||||||||||||||||
| Style and dimension: shall conform to the assemble drawings. | |||||||||||||||||
| Type of actuating: Tactile feedback. | |||||||||||||||||
| Contact arrangement: 1 pole, 1 throw. (Details of contact arrangement are given in the assembly drawings.) | |||||||||||||||||
| Ratings: 12V DC, 50mA (Effective value) | |||||||||||||||||
| Electrical specification: | |||||||||||||||||
| ITEM | TEST CONDITIONS | REQUIREMENTS | |||||||||||||||
| Contact Resistance | Applying a static load of 2 times operating force to the center of the stem, measurements shall be made by 5V DC 10mA or more than 1KHZ AC small-current contact resistance meter. | ≤50m Ω | |||||||||||||||
| Insulation Resistance | Measurement shall be made following application of 100V DC potential, across terminals, and across terminals and cover, for one minute. | ≥100M Ω | |||||||||||||||
| Dielectric voltage proof | 250V AC (50HZ or 60HZ) shall be applied across terminals, for one minute. | No dielectric breakdown shall occur. | |||||||||||||||
| Contact Bounce | Lightly striking the center of the stem at a rate encountered in normal use (3 to 4 times per second), and bounce shall be tested at “ON” and “OFF”
| ON-3msec.max. OFF-8msec.max. | |||||||||||||||
| Mechanical specification: | |||||||||||||||||
| Operating Force | Placing the switch such that the direction of switch operation is vertical and then gradually increasing the load applied to the center of the stem, the maximum load required for the switch to come to a stop shall be measured. | 260±50gf | |||||||||||||||
| Full Travel | Placing the switch such that the direction of switch operation is vertical and then applying static load of 2times operating force to the center of the stem; the travel distance for the switch to come to a stop shall be measured. | 0.25±0.1mm | |||||||||||||||
| Return Force | The sample switch is installed such that the direction of switch operation is vertical and upon depressing the stem in its center to the whole travel distance, the force of the stem to return to its free position shall be measured. | 60gf.min. | |||||||||||||||
| Stop Strength | Placing the switch such that the direction of switch operation is vertical, and then a static load of 30N shall be applied in the direction of stem operation for a period of 1 min. | There shall be no sign of damage mechanically and electrically. | |||||||||||||||
| Waterproofing | Switch placed in water at room temperature 1 m deep soak the location of 120 hours,no water leakage in it. | 120 hours without water seepage | |||||||||||||||
| Soldering heat Resistance | Following the test set forth below the sample shall be left in normal temperature and humidity conditions for 1 h before measurement are made: 1)Solder temperature : 260±5°C 2)Immersion time: 5s±1s | There shall be no sign of damage mechanically and electrically. | |||||||||||||||
| Solderability | Measurements shall be made following the test set forth below: 1)Solder temperature : 235±5°C 2)Immersion time: 2s±0.5 | Except for the edge, the coating should cover a minimum 90% | |||||||||||||||
| Resistance to low temperature | Following the test set forth below the sample shall be left in normal temperature and humidity conditions for 1 h. before measurements are made: 1) Temperature :-30±2°C 2) Time: 96h | Contact resistance: ≤200mΩ | |||||||||||||||
| Heat resistance | Following the test set forth below the sample shall be left in normal temperature and humidity conditions for 1 h. before measurements are made: 1) Temperature: 80±2°C 2) Time: 96h | Contact resistance: ≤200mΩ | |||||||||||||||
| Change of temperature | After 5 cycles of following conditions, the sample shall be allowed to stand under normal temperature and humidity conditions for 1 h. and measurements shall be made. During the test waterdrops shall be removed.
| Contact resistance: ≤200mΩ | |||||||||||||||
| Moisture resistance | Following the test set forth below the sample shall be left in normal temperature and humidity conditions for 1h. before measurements are made: 1) Temperature: 60±2°C 2) Relative humidity: 90% to 95% 3) Time: 96h | Contact resistance: ≤ 200mΩ | |||||||||||||||
| Sulfuration resistance | Following the test set forth below the sample shall be left in normal temperature and humidity conditions for 1h. before measurements are made: 1) H2S gas concentration: 3ppm±1ppm 2) Time: 72h 3) Temperature: 40±2°C(90~95%RH) | Contact resistance: ≤ 200mΩ | |||||||||||||||
| Salt Mist | The switch shall be checked after following test: 1) Temperature: 35°C±2°C 2) Salt solution : 5±1%(solids by mass) 3) Time: 24h±1 hour After test,salt deposit shall be removed by running water. | No remarkable corrosion shall be recognized in metal part. | |||||||||||||||
| Operation life | Measurement shall be made following the test set forth below: 1) DC 12V, 50 mA resistive load 2) Rate of operation: 120 times/min. 3) Operating Force:320~350gf 4) Average fault-free life: 100,000 cycles | Contact resistance: ≤200mΩ Contact bounce: ≤10ms Operating Force: initial value±30% | |||||||||||||||
| Vibration | Measurement shall be made following the test set forth below: 1) Vibration frequency range: 10Hz to 55Hz to 10Hz 2) Amplitude: 1.5mm 3) Direction of vibration:Three mutually perpendicular direction including the direction of stem travel 4) Duration: Each 2hours. | ||||||||||||||||
| Soldering conditions: | |||||||||||||||||
| ITEM | RECOMMENDED CONDITIONS | ||||||||||||||||
| Hand soldering | Please practice according to below conditions: 1) Soldering temperature: 350°C Max. 2) Continuous soldering time: 3 s Max. | ||||||||||||||||
| |||||||||||||||||
| Note: 1,After switches were soldered, please be careful not to clean switches with solvent. 2,Right after switches were soldered;please be careful not to load to on the knobs of switches. Please be careful not to pile up PCB. after switches were soldered. 3,Preservation under high temperature and high high humidity or corrosive gas should beavoided Especially . When you need to preserve for a long period ,do not open the carton. | |||||||||||||||||
More product:
Use of equipment:
Express delivery :
Sample:
1. Free charge sample: Could provide(less than 10 PCS),freight collect
2. Samples time: Need 7-10 days to preparing the samples after receiving the payment.
3. Samples payment term: T/T, PAYPAL, Western union
Quality Guarantee:
1.Strictly quality control before leave factory
2. Quality guarantee within one year
Advantage:
1.Low MOQ: 1000PCS
2.New design Accepted: As your requirement
3.Good Service: Customer as God
4.Good Quality: Strict quality control and good reputation
5.Fast & Cheap Delivery: Big discount from express agent (Long-term Contract)
Order Guide:
| 1. Inquiry-Professional quotation. |
| 2. Confirm the price, lead time, packing requirement, payment term etc. |
| 3. OMTER sales send the Proforma Invoice with OMTER seal. |
| 4. Customer make the payment and send us Bank receipt. |
| 5. Will inform client that we have got the payment, arrange the production & inform the estimated time. |
| 6. After delivery will inform the tracking number and check the status for clients. |
| 7. Feedback to TALL about Quality , Service, Market Feedback & Suggestion. And we can do better . |
Company Picture:
Contact Us
- Yueqing Omter Electronic & Technology Co., Ltd.
- Contact nameSweetie lin Chat Now
- Phone0086-0577-27811881
- Addresshousuo industrial,yuecheng town., Wenzhou, Zhejiang
Product Categories
| Digital potentiometer | Hot Sale | hot switch | Joysticks |
| KNOBS CATALOG INDEX | New Products | Other | potentiometer |
| Repeat joystick | Repeat KNOBS | repeat product | Repeat products |
| sakae potentiometer | switch |
New Products
-
TS0633c-0508a tact switch smd
-
TS0542-0155C electronic tact switch
-
TS0641-0431b push button tact switches
-
TS0649a-0502c TACT SWITCH RoHS
-
TS0672-0723c-b 4 pin tact switch
-
TS0671-0703c-g tact switch manufacturers
-
TS0672-0853c-r tact switch waterproof
-
TS0673-1003c-b waterproof tact switch
-
TS0673-0853b-b led tact switch
-
TS0672-0854c pin tact switch
-
TS0674-0703b-b tact switch with led
-
TS0678-1003b-b wholesale Tact Switch
Popular Searches
- buzzer
- lock switch
- control switch
- light switch
- pedal switch
- button push
- push button switch
- button switch
- electrical switch
- wall switch
- tact switch
- tact
- waterproof switch
- pushbutton switch
- tactile switch
- push switch
- dimmer switch
- fan dimmer
- bell switch
- hotel switch
- electrical contacts and contact material
- electronic switch
- door limit switch
- electric switch
- power switch
- equipment switch
- foot switch
- metal pushbutton switch
- led pushbutton switch
- light pushbutton switch
Recommended Products
- DC12V 24V water lamp wireless 3-button dimming controller suitable for living room and staircase lighting
- xb2 lay5 10a 600v Heavy duty equipment button emergency stop switch 22mm Warning circle
- 19mm 1no1nc 2no2nc emergency stop push button ip67 for Charging pile
- HBAN ip67 NO normally close elevator control lock switch Emergency Stop button 16mm
- New 913A0123H01 oil level sensor, York screw compressor oil level control fault repair
- Side press sinking board switch, game controller, light touch switch, handle button 3 * 4 * 3.5, side press smiling face switch
- Original C&K genuine PTS647SK38SMTR2 LFS 4.5x4.5x3.8-250GF SMT switch
- Original C&K genuine PTS645SK43SMTR92 LFS 6X6X4.3H 260GF SMT switch
- Original C&K genuine PTS641TK25SMTR2LFS 6.2x6.2x2.5 five pin 250GF SMT switch
- USB3.0 two-way switch usb converter
- GO SWITCH switch
- TOPWORX switch
Find Similar Products By Category
- Electrical & Electronics > Switch > Push Button Switch
- Please Enter your Email Address
- Please enter the content for your inquiry.
We will find the most reliable suppliers for you according to your description.
Send Now
Yueqing Omter Electronic & Technology Co., Ltd.
AIBot OnlineThis conversation is AI-generated. Contact manufacturer before transaction to confirm info.
-
Sweetie lin
Hi there! Welcome to my shop. Let me know if you have any questions.
Your message has exceeded the limit.
- Contact supplier for lowest price
- Customized Request
- Request Sample
- Request Free Catalogs
Your message has exceeded the limit.
-
Purchase Quantity
-
*Sourcing Details
Your inquiry content must be between 10 to 5000 characters.
-
*Email
Please enter Your valid email address.
-
Mobile