LED bulb power

MODEL

LPLC-18-350                                      

LPLC-18-700

CURRENT RANGE

6~48V                                            

6~25V

RATED CURRENT

  350mA                                   

700mA

RATED POWER

16.8W

17.5W

RIPPLE & NOISE (max.)  Note.2

300mVp-p                         

200mVp-p

VOLTAGE TOLERANCE   Note.3

5.0%

LINE REGULATION

1.0%

LOAD REGULATION

2.0%

SETUP, RISE TIME

3600ms, 150ms / 115VAC

HOLD UP TIME (Typ.)

20ms/115VAC at full load

INPUT

VOLTAGE RANGE

90 ~ 132VAC   127 ~ 186VDC

FREQUENCY RANGE

47 ~ 63Hz

EFFICIENCY (Typ.)

82%

80%

AC CURRENT (Typ.)

0.5A/115VAC

INRUSH CURRENT (Typ.)

Cold start 40A/115VAC

LEAKAGE CURRENT

0.25mA / 120VAC

PROTECTION

CURRENT LIMIT

5% rated output current

Protection type : Constant current limiting type

SHORT CIRCUIT

OVER VOLTAGE

50.4~ 60V                                       

28.75~ 33.75V

Protection type : Shut off o/p voltage, clamping by zener diode

OVER TEMPERATURE

Tj 140^oC  t ypically (U1) Detect on main control IC

Protection type : Hiccup mode, recovers automatically after temperature goes down

ENVIRONMENT

WORKING TEMP.

-30 ~ +70^oC (Refer to output load derating curve)

WORKING HUMIDITY

20 ~ 90% RH non-condensing

STORAGE TEMP., HUMIDITY

-40 ~ +80^oC , 10 ~ 95% RH

TEMP. COEFFICIENT

0.03%/^oC (0 ~ 50^oC )

VIBRATION

10 ~ 500Hz, 2G 12min./1cycle, period for  60min. each along X, Y, Z axes

SAFETY &EMC(Note 4)

SAFETY STANDARDS

IP67 approved; design refer to UL1310 Class 2,TUV EN60950-1, EN61347-2-13, CAN/CSA C22.2 No. 223-M91

WITHSTAND VOLTAGE 

I/P-O/P:3KVAC

ISOLATION RESISTANCE

I/P-O/P:>100M Ohms / 500VDC / 25 / 70% RH

EMI CONDUCTION & RADIATION

Compliance to EN55022 (CISPR22) Class A, FCC part15

HARMONIC CURRENT

Compliance to EN61000-3-2 Class A,EN61000-3-3

EMS

IMMUNITY

Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, Light industry level,  criteria A

OTHERS

MTBF

1200.6K hrs min. MIL-HDBK-217F

DIMENSION

140*30*22(L*W*H)

PACKING 

0.175Kg; 70pcs/13.3Kgs/0.71CUFT

NOTE

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25^oCof ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. Derating may be needed under low input voltage. Please check the static characteristics for more details.

5. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.