We require the following dairy processing equipment with quantity 1 unit each:  
- Raw Milk Cooling Tank (250L capacity)  
- Pasteurizer with Cooling (500L/h capacity)  
- Separation System including 50L cream tank and homogenizer (500L/h input)  
- Homogenizer (470L/h capacity, 170-200 bar)  
- Canning line with retort (1325 cans/batch capacity)  
- Bottling line for 300mL and 1000mL containers  
- Labelling/Coding machine (1325 containers/hr capacity)  
Please provide quotation for complete set of equipment.

We require design and supply of steam boiler systems for LPG processing with the following specifications:  
1. Storage Bullets: 50 m3 mounded design, ASME VIII Div.1 compliant, 17-20 barg pressure rating, dual PRVs with changeover system, complete with level monitoring and safety features.  
2. Vaporizers: Water-bath type with 400 kg/h capacity base configuration or 200 kg/h modular setup, including safety relief systems and temperature controls.  
3. Full compliance with ASME B31.3 piping standards and NFPA 58 safety requirements for entire system integration.  
All components must include proper pressure regulation stages from 6-8 barg down to 0.1-0.3 bar burner supply.

We require a pump pressure test system capable of handling maximum pressure of 725psi (50 bars) with 1/2" NPT pressure hose connection. The unit should have 3.6 gallons tank capacity and operate within maximum temperature of 50°C (120°F). Required specifications include piston volume of 2.3 cubic inches, dimensions 28"x8.5"x9.5", and weight under 14lbs. Please provide RIGID Model 50557 (Catalogue 1450). Looking to purchase 2 units for leak detection in heating, potable water, fire sprinkler, compressed air, small bore pipe lines, and oil systems.

Require a custom-built misting system with below specifications:

Dual-Liquid Dosing:
- Two separate 5-20L concentrate tanks
- Automatic proportional mixing (1-2% per liquid)
- Integrated with main water line

Pump Requirements:
- Stainless steel plunger pump
- 50-70 bar pressure capacity
- Flow rates: 1L/min (20 nozzles), 3L/min (60 nozzles), 12-15L/min (300 nozzles)

Nozzle Specifications:
- Stainless steel/brass construction
- 3-10μm droplet size
- Anti-drip function

Control System:
- Digital/PLC controller with dosing ratio adjustment
- Programmable misting intervals and cycles
- Optional remote/app control

Compact design preferred (≤50cm x 60cm). Pre-filtration system required to prevent nozzle blockage.}

We require a complete wheel wash system for heavy-duty trucks and construction vehicles. Essential specifications include:
- 3100 l/min water pump capacity with 1.7 bar pressure
- Hot-dip galvanized steel frame and stainless steel nozzles
- Integrated clarifier tank (~20 m3) and automatic detection system
- 3×400V/50Hz power supply with CE compliance
- Minimum 15-ton axle capacity and 3500mm passage width

The pump must be from established brands with reliable spare parts network in EU. Please provide EXW and CIF (Skalica) pricing, lead time details, and warranty terms. Include Q-H curve documentation and technical compliance certificates.

I need pressure vessel tanks with these specifications:
- Model: TY-06-100L
- Minimum 100L capacity
- SS-316 grade metal construction
- 450mm diameter & 940mm height
- 10 BAR minimum working pressure
- Interchangeable potable bladder membrane
- Red epoxy-coated exterior
- Floor-mounted type with 1.5" water connection
- Suitable for central heating systems
Please confirm availability and provide technical compliance documentation.

We require airless bottles with pump systems for liquid dispensing in restaurant and bar environments. The solution must prevent air contamination while ensuring easy operation for staff. Specifically interested in pump sprayer mechanisms that allow controlled dispensing. Need confirmation whether the airless design uses internal bags or other methods. Budget flexible but require product examples with pricing tiers based on order quantity. No specific quantity determined yet but exploring options for bulk purchases.

Urgently require following rechargeable NiCd cells:  
1. NiCd Cell 1.2V 4.5AH D Type (Bar of 5 Cells)  
2. NiCd Cell 1.2V 1.4AH RR Type  

Prefer to communicate through platform messaging system for efficient processing. Please provide specification sheets and compliance certifications for the cells.

We are establishing a Japanese teppanyaki restaurant and require professional assistance for:
1. Interior design solutions including hood cladding and ready-to-install wall fittings
2. Custom-built teppanyaki equipment:
  - Commercial teppanyaki grill with integrated table system
  - Yakitori bar grilling equipment
  - Sushi/sashimi preparation counter
3. Complete HVAC system integration for kitchen areas

Please provide:
- Technical specifications
- Minimum order quantities
- Pricing structure
- Production lead times
- Installation support capabilities

Requirement for Titanium Grade 2 Connection Fittings:  
? Material: Titanium Grade 2, Schedule 40S  
? Specification: NPTF threaded design compliant with NORSOK M-601 standard  
? Service Range: 30 bar / Class 150 / -30°C to 70°C  
? Quantity: 100 units  
? Delivery: December  
? Documentation: Staggered pricing required with technical drawings review  
? Application: Flexible deluge systems for international engineering projects  
Please provide commercial terms and production feasibility.

 
We are interested in purchasing head tie. Please provide:  
1. Product specifications and available designs  
2. Minimum order quantity (MOQ)  
3. Competitive pricing  
4. Estimated production lead time  

Suppliers with OEM/ODM capabilities are preferred. Kindly include product catalogs and certification details.

Supply and delivery of ductile iron pipes with a diameter of 1200 mm (ISO) and a nominal pressure of PN16 bars, with a Polyethylene (PE) protection sleeve against SO? and salinity, in accordance with the approved drawings and Technical Specification Volume 1 and Volume 2, from the factory to the construction site. 

We need 78,000 cartridges for water purification system, Membrane element of SEPART IMT 10060 UF/MB - G ultrafiltration unit. Active filtration area: 60 m2. Maximum temperature: 40 °C. Maximum pressure: 7.5 bar. Allowable pH range of incoming water: working mode 3÷10, flushing 1÷13. Capillary material: PESM. Membrane length: 1682 mm. Membrane diameter: 250 mm. Weight: 31.5 kg. Preferably on DAP terms, supplier's warehouse in Almaty, Kazakhstan.

Ask if manufacture ZYF - 5L reactor model (or close to it) and compare its parameters with Parr 5410 Fluidized Bed Reactor. Known parameters: Fluidized Bed Reactor, Pressure 120 bar, Temperature 500°C, Volume 5 l, Material SS316L with Al?O? coating, Accessories Automatic N? purge system

Quote the following parts: Full body harness (quick connect chest and leg straps, Back D - ring, Universal size, Weight Capacity 140 kg, Buckle Material Zinc Plated Steel, Q = 8); Self - Retracting Lifeline (Stainless Steel Cable, Swivel Snap Hook, 6 m length, Swiveling anchorage connector loop and carabiner, thermoplastic housing design, lightweight design, Weight Capacity 140 kg, Quick activating speed - sensing locking system, Q = 8); Beam accessories (For beams of width 76 to 300 mm, Complete hands - free horizontal mobility, Double - shielded wheel bearings, corrosion resistant, Weight Capacity 140 Kg, Material Zinc Plated Steel, Rotating D - ring tie - off point, Q = 8)

We have a request for centerless lathe. Could you please send me a quotation according to technical parameters? Please specify the price FOB. Technical parameters: 1. Raw bar diameter: 8 to 32mm; 2. Bar length: a?¤ 3000mm; 3. Bar material: D16T, AMg3; 4. Machining accuracy: a?¤ h9 tolerance; 5. Surface roughness: a?¤ Ra 1.6??m; 6. Surface ovality: a?¤ 0.05mm; 7. Surface straightness: a?¤ 1%; 8. Spindle rotation speed: a?￥ 2000rpm; 9. Feed rate: a?￥ 0.5m/min; 10. Motor power: a?￥ 30kW; 11. Machine maximum length: a?¤ 10,000mm; 12. CNC system (Russian interface): Fanuc 0i; 13. Standard accessories: Included; 14. Additional accessories: Included; 15. Russian - language user manual: Included

1 X VEGAPULS 64, RADAR SENSOR; FOR CONTINUOUS LEVEL MEASUREMENT OF LIQUIDS; MAKE: VEGA; PART NUMBER: PS64.AXGFNIHXKMKXX (eID: ZA99712825); APPROVAL X : FOR EX-FREE AREA; ANTENNA VERSION / SECOND LINE OF DEFENCE G : FLANGE WITH ENCAPSULATED ANTENNA SYSTEM / WITH PROCESS FITTING / MATERIAL FN : FLANGE DN100 PN40 Form C, DIN2501 / 316/316L MATERIAL / SEAL / PROCESS; TEMPERATURE I : PTFE / PTFE / -40... 130 °C ELECTRONICS H : TWO-WIRE 4 ... 20 mA/HART SUPPLEMENTARY ELECTRONICS X : WITHOUT OPTIONAL OVERVOLTAGE PROTECTION : WITHOUT HOUSING / PROTECTION K : PLASTIC SINGLE CHAMBER / IP66/IP67 CABLE ENTRY / CONNECTION M : M20x1.5 / CABLE GLAND PA BLACK (?5-9mm), STANDARD; DISPLAY/ADJUSTMENT MODULE PLICSCOM K : MOUNTED; WITH BLUETOOTH, MAGNETIC PEN OPERATION; ADDITIONAL EQUIPMENT X : WITHOUT CERTIFICATES X : No MAX. MEASURING RANGE : 30.000 m OPERATING INSTRUCTIONS : EN - ENGLISH NUMBER OF OPERATING INSTRUCTIONS : 1 MIN. PROCESS PRESSURE IN BAR : -1.000 MAX. PROCESS PRESSURE IN BAR : 16.0

We are looking for square stick 4x4x400 mm Bar Tools

Bar Tools

Could you please provide your commercial proposal for the next lines: SENSOR,PRESSURE,S4250B076032 ,1-16BAR SENSOR,TYPE: PRESSURE; EQUIPMENT: SERVICE AIR SYSTEM;TECSIS, ART: S4250B076032, PRESSURE RATE: 1-16BAR, PMAX: 60 BAR, IMAX: 4.0, UMAX: 250VAC---2 EACH.

One of my customers is interesting by cnс lathe machine, approximately parameters are below. 1. Parameters of the workpiece 1.1 Maximum diameter above the bed mm - 520 1.2 Maximum machining diameter mm - 350 1.3 Maximum machining length mm - 500 1.4 Standard chuck size inch - 10 2.CNC system 2.1 Siemens 828D 3. Spindle 3.1 Drive type - Belt drive 3.2 Spindle flange type A2-8 3.3 Through-hole diameter mm - 74 3.4 Bar diameter mm - 63 3.5 Spindle front bearing diameter mm - 120 3.6 Spindle speed rpm - 50-3500 4. Turret 4.1 Height to center of turret mm - 100 4.2 Number of tool positions - 12 4.3 Diameter mm - 380 4.4 Maximum diameter of the boring mandrel mm - 40 4.5 Cutter cross-section size mm 25 x 25 5. Feed 5.1 Positioning X, Z mm - ±0.005 5.2 Repeatability X, Z mm - ±0.003 6. X axis 6.1 Stroke in the X axis mm - 200 6.2 Traveling speed m/min - 24 6.3 Ball screw diameter and pitch mm - 40 x 10, class C3 6.4 Guideway width mm- 35 roller, class P4 7. Z axis 7.1 Z-axis travel mm - 510 7.2 Traveling speed m/min - 24 7.3 Ball screw diameter and pitch mm - 40 x 10, class C3 7.4 Guideway width mm - 35 roller, class P4 8. Hydraulic tailstock 8.1 Quill type MT-5 8.2 Quill stroke mm - 100 8.3 Tailstock travel mm - 300 8.4 Maximum clamping force kg - 20-25 

 We are interested in purchasing a saw for cutting polymer materials. Materials information: Polymer materials of rectangular and cylindrical shape. ? The rectangular section of the cut is 80/135 mm. ? Cylinder with a cutting cross section of ?180 mm. The inner hole is ? 32mm. ? ISO 868 SHORE D hardness from 42 to 52; ? ISO 1183 from 0.98 to 1.4 kg/cm3 Hardware requirements: - The machine must be equipped with adjustable pneumatic clamps for reliable and accurate fixation of the profile. Automatic feeding of blanks. - The large diameter of the saw blade (at least 450 mm) and movable stops allow you to cut large workpieces. - The machine must be able to adjust the feed rate to adjust the optimal profile cutting mode - After cutting is completed (or in case of an emergency stop), the saw blade automatically returns to its original position (descends into the machine cabinet) - The machine must have a water cooling system, STANDARD ACCESSORIES for a deflated pneumatic pistol. Measuring roller in quantity of 1 pc. (length 1000mm). A saw blade with a diameter of at least 450 mm. - The machine must be provided with automatic coolant supply when cutting workpieces. - Electric motor of at least 4kW, 380V/3F/50Hz Saw blade (diameter/ fit) 450mm/30-32mm Disc rotation speed 3000 rpm Compressed air supply 6-8 bar, 35lit/min We are waiting for your prompt response and commercial offer!