Bently Nevada 3500/05-01-02-00-00-00 System Rack (Framework Module) – Backplane & Housing for 3500 Machinery Protection

• Warranty: 365 days

• Delivery: 1 week if in stock; no more than one month at the latest

• Payment: 50% advance payment; full payment before delivery

• Express: FedEx, UPS, DHL

• Each unit is inspected before shipment; careful packing for sensitive instrumentation frames

• 14-slot 19-inch rack-mount format – A practical layout that typically accommodates one or two power supplies, a TDI, and multiple monitoring modules without cabinet rework.

• Robust backplane distribution – Clean, reliable power and signal bus interconnects across the rack, supporting redundancy strategies.

• Compatible with the full 3500 family – Works with 3500/15 Power Supplies, 3500/22M TDI, and vibration/position/speed modules (e.g., 3500/40M, 3500/42M, 3500/60, 3500/45).

• Rear I/O wiring concept – Field terminations on the rear I/O modules keep the front clean for module access and make maintenance quicker.

• Service-friendly design – Modules can be replaced without disturbing the field wiring; in many cases, this shortens planned outages.

• Proven in critical machinery – Commonly used on turbines, compressors, and high-speed rotating assets where API and plant standards matter.

This rack is widely used where continuous protection and condition monitoring are mandatory: steam and gas turbines, centrifugal and screw compressors, large pumps and fans, generators, gearboxes, and critical motors. In many cases, plants standardize on the 3500 platform for API-compliant machinery protection in oil & gas, petrochemical, power generation, and paper & pulp. One reliability engineer told me they kept a spare rack on the shelf so they could re-frame a unit during a turnaround without touching field wires—just move the modules and go.

• Reliability under load – The 3500 platform has a strong track record on high-vibration assets; the rack’s mechanical stability helps reduce nuisance trips.

• Lifecycle flexibility – Mix and match modules as your assets change—usually no cabinet redesign thanks to the standard rack footprint.

• Lower downtime costs – Rear I/O wiring stays put while you replace or upgrade front modules, which typically means faster turnarounds.

• Compatibility & support – Works with common 3500 accessories and software; easier spares strategy across multiple sites.

• Cabinet & mounting – Install in a clean, dry enclosure; 19-inch rack per EIA standards. Allow front clearance for module access and rear clearance for I/O wiring.

• Ventilation – Provide adequate airflow; avoid hot spots near VFDs or high-loss power equipment. Derating may apply at higher ambient temperatures.

• Wiring practices – Separate transducer/signal cables from power; follow shield and ground instructions for each module’s I/O card.

• Redundancy options – Consider dual power supplies in critical racks; verify LED/alarm states after any power work.

• Routine care – Periodically dust the rack, check backplane connectors for secure seating, and keep firmware/software of monitoring modules current (where applicable).

• Calibration workflow – The rack itself doesn’t require calibration; perform transducer and channel calibrations on the installed monitoring cards as per site procedures.

• 3500/15 Power Supply (AC or DC input options; consider dual PS for redundancy)

• 3500/22M Transient Data Interface (TDI) for Ethernet communications and System 1 connectivity

• Monitoring modules such as 3500/40M (Proximitor/Seismic), 3500/42M (Proximitor/Seismic), 3500/60 (Temperature), 3500/45 (Position)

• Rear I/O modules matched to each monitoring card; appropriate terminal kits and shielded cabling

• CE marking and RoHS compliance for most configurations

• UL/cUL listing for industrial control equipment (typical for the 3500 platform)

• Manufactured under ISO 9001 quality systems

• Hazardous area approvals may depend on installed modules and I/O—verify per project spec

• Warranty: 365 days from shipment

- Can I reuse my existing 3500 modules in this rack? In most cases, yes—module compatibility is a core strength of the 3500/05 frame.
   - Do I need to re-terminate wiring when swapping racks? Typically no; field wiring stays on the rear I/O, which saves time during turnarounds.
   - Is Ethernet built into the rack? Communication is provided by the 3500/22M TDI module, not by the rack itself.