Bently Nevada 9200-06-01-10-00 Velocity Seismoprobe – Reliable Case Vibration Sensing for Rotating Machinery

• Warranty: 365 days

• Lead time: 1 week if in stock; no more than 1 month at the latest

• Payment: 50% advance; full payment prior to delivery

• Express delivery: FedEx, UPS, DHL

• Self-powered velocity sensing – Moving-coil design generates a dynamic voltage proportional to case vibration; no external power required.

• Case-mounted measurement – Ideal for bearing housings and machine casings where direct shaft probes aren’t practical.

• Industrial frequency band – Covers the typical machinery vibration range for balance, misalignment, looseness, and mechanical resonance checks.

• Integral shielded cable – The “-10” build typically indicates an integral cable length suited for neat routing to the junction box or monitor.

• Broad monitor compatibility – Works with Bently Nevada 3500/3300/1900 series and most vibration inputs expecting a velocity signal.

• Rugged build – Sealed, field-proven construction for harsh industrial environments with stable long-term sensitivity.

You’ll typically see the 9200 on:

• Power generation – steam turbines, generator bearings, boiler feedwater pumps.

• Oil & gas – compressors, pumps, and API-compliant trains where case vibration trending is standard.

• Chemicals & petrochem – large process pumps and fans with continuous monitoring.

• Pulp & paper, mining, cement – rugged drive trains and critical conveyors/fans.

One thing I appreciate is how the 9200 series handles low-frequency machinery issues. In many cases, you get cleaner velocity trends without needing an external integrator, which keeps channel configuration simple in the rack.

• Compatibility – Drop-in fit for Bently Nevada 3500/3300/1900 monitors and widely supported by third?party CM systems.

• Low lifecycle cost – No power supply, minimal failure modes, and straightforward spare strategy.

• Reliable trending – Stable sensitivity for long-term case vibration baselining and alarms.

• Simple wiring – Two-wire dynamic output reduces channel complexity compared to accelerometer + integrator setups.

• Procurement certainty – Mature, widely deployed product line with predictable performance and stocking options.

• Mounting – Stud-mount on a smooth, clean surface close to the bearing housing. Maintain consistent orientation across machines for comparable data.

• Wiring – Use the integral shielded cable; land the shield at the monitor/junction box per plant grounding practices. Keep clear of VFD and high-voltage runs to reduce noise.

• Cabinet & environment – Route into a ventilated cabinet or junction box; use proper strain relief and avoid tight bend radii.

• Safety – De-energize adjacent equipment during installation. If installed in hazardous areas, verify the exact option code approvals before commissioning.

• Upkeep – Inspect mounts and cable strain relief during outages. Verify channel sensitivity during periodic calibrations and update monitor firmware/settings as required.

Field remark from a maintenance supervisor (combined-cycle plant): “Swapped to 9200s on the main condensate pumps last outage. Cabling was straightforward, and the 3500 channels lined up with our existing alarm setpoints with minimal rework.”

• CE conformity and RoHS compliance are available on standard 9200 series builds.

• Hazardous-area approvals (e.g., ATEX/IECEx/CSA) exist on certain option codes; confirm against 9200-06-01-10-00 before use in classified zones.

• Our warranty: 365 days from delivery.

• Bently Nevada 3500 Series rack monitors (e.g., 3500/42M) for velocity channels and alarms.

• Bently Nevada 1900/65A or 1900/55 monitors for stand?alone machine protection.

• Junction boxes and stainless mounting studs/adapters for difficult surfaces.

• Shielded extension leads and cable glands suitable for the 9200 series integral cable OD.

If you’re standardizing on case vibration for critical pumps and fans, this 9200-06-01-10-00 build hits a practical balance: fast to deploy, dependable signal quality, and in most cases no surprises during commissioning. If you’d like, share your monitor model and channel card type; I can double?check sensitivity settings and wiring polarity so your first trend looks right from day one.