Module spare parts DSQC604 3HAC12928-1

Focus on DCS, PLC, robot control system and large servo system.

Main products: various modules / cards, controllers, touch screens, servo drivers.

Advantages: supply of imported original products, professional production parts,

Fast delivery, accurate delivery time,

The main brands include ABB Bailey, Ge / fuanc, Foxboro, Invensys Triconex, Bently, A-B Rockwell, Emerson, ovation, Motorola, xyvom, Honeywell, Rexroth, KUKA, Ni, Deif, Yokogawa, Woodward, Ryan, Schneider, Yaskawa, Moog, prosoft and other brands

TPreparing to Install an Optional SFP Transceiver Before removing the pluggable transceiver from the antistatic packaging, Enterasys Networks recommends that you use an antistatic wrist strap (not supplied) to prevent damage from static discharge. To use the wrist strap, refer to the instructions provided with your antistatic wrist strap. 1. Remove the pluggable transceiver from its packaging. 2. If there is a protective dust cover in the pluggable transceiver connector, do not remove it at this time. Installing an Optional SFP Transceiver This section describes how to install an SFP transceiver into A4 ports. To install an SFP that has an RJ45 connector, refer to Figure 2‐14; for an SFP with an MT‐RJ connector, refer to Figure 2‐15; for an SFP with an LC connector, refer to Figure 2‐16; and proceed as follows: 1. With an antistatic wrist strap attached to your wrist, remove the transceiver from its packaging. If there is a protective dust cover in the transceiver connector, do not remove it at this time. 2. Hold the transceiver so that the connector will seat properly. 3. Carefully align the transceiver with the port slot as shown in Figure 2‐14, Figure 2‐15, and Figure 2‐16. 4. Push the transceiver into the port slot until it “clicks” and locks into place. Warning: Fiber-optic SFPs use Class 1 lasers. Do not use optical instruments to view the laser output. The use of optical instruments to view laser output increases eye hazard. When viewing the output optical port, power must be removed from the network adapter. Advertencia: Los SFPs de fibra optica usan lasers de clase 1. No se debe usar instrumentos opticos para ver la potencia laser. El uso de los instrumentos opticos para ver la potencia laser incrementa el riesgo a los ojos. Cuando vean el puerto de la potencia optica, la corriente debe ser removida del adaptador de la red. Warnhinweis: SFPs mit Fiber-Optik Technologie benutzen Laser der Klasse 1. Benutzen sie keinesfalls optische Hilfsmittel, um die Funktion des Lasers zu überprüfen. Solche Hilfsmittel erh?hen die Gefahr von Sehsch?den. Wenn sie den optischen Port überprüfen m?chten stellen Sie sicher, dass die Komponente von der Spannungsversorgung getrennt ist. Caution: Carefully follow the instructions in this manual to avoid damaging the SFP and switch equipment. The SFP and switch equipment are sensitive to static discharges. Use an antistatic wrist strap and observe all static precautions during this procedure. Failure to do so could result in damage to the SFP and switch equipment. Always leave the SFP in the antistatic bag or an equivalent antistatic container when not installed. Precaución: Siga las instrucciones del manual para no da?ar el SFP ni del aparato, puesto que son muy sensible a las descargas de electricidad estática. Utilice la pulsera antiestática y tome todas las precauciones necesarias durante este procedimiento. Si no lo hace, podría da?ar el SFP o del aparato. Mientras no esté instalado, mantenga el SF