PA-03 Audio Tube Preamplifier w/ VU Meter 6N11 Standard Balanced Version Refer To ARC LS22

PA-03 Audio Tube Preamplifier w/ VU Meter 6N11 Standard Balanced Version Refer To ARC LS22

Description:
Standard Balanced Version features transformers for input and output, with a set of balance interfaces for input and output separately.

It uses 4 pieces of thin film alloy + oxygen-free copper wire winding, the package is shielded by copper foil for 3 layers, the frequency response is flat. The measured frequency response is 20Hz -22KHz ±0.1DB (better than most audio transformers). The sound through the audio transformer is detailed and clear, dynamic and wide, and very friendly to ears.

Referring to the circuit for American Audio research LS22, it adopts a balanced dual mono design. The sound of this preamp is smooth and durable, high frequency extension is good, middle and low frequency mellow, deep dive, it gives people the feeling that it is very quiet and suitable for listening for a long time at a moderate speed. The even harmonics of -60dB make the sound more rounded and durable!

Sound Characteristics:
Use thin-film alloy transformer for conversion, the dynamics are better than the single-ended version, and the voice is sweet

Functional Features:
1. Optional power supply upgrade kit (refer to German power black box for OCTAVE tube amplifier)
2. RCA ports are changed to rhodium-plated RCA
3. Potentiometer for ALPS27, with good sound quality and better reliability
4. Increase the partition between the circuit board and the transformer to prevent interference
5. The specially designed relay input selection circuit will not cause the sound of other groups to crosstalk the current channel (this problem will occur in many machines)
6. Output delay design to prevent the DC output impact of power amplifiers and speakers
7. Two groups of high voltage adopt op amp servo + FET for voltage stabilization, low temperature wave, high speed, quieter background, better sound quality reproduction
8. The hand swing can turn off (only the hand swing can be turn off, not the light)
9.Filament power supply AC and DC switching (note: filament AC power supply is temporarily cancelled, please contact us if you need filament AC power supply)
10. Equipped with treble and bass adjustment function, which can also be turn off (relay switch). The tone circuit has no common bass mixing and treble harshness
11. The electrolysis of the power supply part and the red for WIMA are consistent with the parameters of the original machine, and the sound is neutral and balanced
12. Transformer: Japan Z11 EI86 iron core 90W
13. Chassis: All aluminum standard size: 430*330*100mm, with VU meters, weight 10KG, upper cover without screw, large R angle at the edge, perfect CNC technology, there is no better case than ours at the same price
14. Standard electron tube: Chinese 6N11 electron tube x 4 can be replaced by E88CC, 6922 and 6DJ8
15. Output: Balanced version boasts 2 groups of RCA+1 group of XLR balanced output at the same time
16. Input: Balanced version with 1 set of XLR + 3 sets of RCA

More Details:
- With transformers for input and output
- With a set of balance interfaces for input and output separately
- Four thin-film alloy input voltage transformers and output voltage transformers, with flat frequency response, low distortion and good dynamics
- Input Interfaces: three groups of RCA and one group of XLR balance
- Output Interfaces: Two groups of RCA, one group of XLR balanced output at the same time
- Each machine is shipped after passing software test, and the tubes are installed in the best position. Please not change the tubes casually, otherwise it will affect the sound

Parameters:
- Signal-to-noise ratio: filament DC power supply 100dB (when the output is 2V, the volume is about 2 o'clock position)
- Magnification: 6.5 times
- Frequency range: 10HZ-100K (±0.5dB)
- Bass adjustment range: 50HZ±6.5dB
- Treble adjustment range: 15KHZ±6.5db
- Input impedance: 100KΩ
- Output impedance: 200Ω
- Maximum output undistorted voltage: 25V RMS
- Distortion: 0.2% (when VU meters are closed, no negative feedback)

Package Included:
- 1 x Tube Preamplifier

Note:
- It is assembled.
- The position of each tube is specific (tested with the instrument in the best condition), please not insert it randomly, otherwise it will affect the effect.
- Full balance requires 2 machines.
- Components for WIMA and coupling capacitors are second-hand. Please make sure that you don't mind before purchasing.
- Filament AC power supply is an optional function (cancelled by default). If you need to retain the AC power supply, please contact us, but noise level is not guaranteed.
- Only the machine is included, accessories are not included in the package.

Detail photo

FAQ 

Q1. Can I have a sample order?

A: Yes, we welcome sample order to test and check quality.

Q2. What about the lead time?

A: Sample ususally take within 3 working days.

Q3. Do you have any MOQ (minimum order quality)limit?

A: For standard product, usually 1pcs/item. For the OEM order, MOQ at least 50pcs/item.

Q4. How to proceed an order?

A: After buyer confirm the product&price is ok and ready to buy, order will be please tell us your delivery address, phone number, sometimes need email. Then we can draft the order and it will have a alibaba paying link.

Q5. After paid, what info of the supplier provided?

A: Tracking number

Q6: Do you offer guarantee and after-service for the products?

A: Yes, 6- 12 months warranty for our products. Note: We will do not take the responsibility for Man-made damage or improper operation. Delivery demage will be negotiate.

Packing and Shipping

Package: Normally we use the standard paper package to export worldwide.

Shipping : 

1. By Couriers: DHL, UPS, FEDEX, TNT are the main courier  we are co-operating at present.

2. By chinese small parcel, usually for the customer to save the cost. But Chinese small parcel have the risk for lost parcel. Note: If we got the parcel back, we only can refund the item cost. If we didn't get the parcel,then sorry we can't refund any.

3. By Air: Delivery from the Shenzhen airport to customers’ destination city air port.

4. By Sea: Delivery from the Shenzhen sea port .

Company information

TZT has been speciliazing in Business & Industry,Hobbies & Toys,CNC Products and Health care supplies for over 5 years.We committed to enhance customer satisfaction by continually improving the process with a vision of expertise in the field. 
Aiming to provide high quanlity products and great service for buyer,we are strict on product quanlity control and offer instant communication service.Welcome to contact us!

Our Advantages:
-  Source only the best consumer goods and ensure the highest quality.
-  Streamline the buying and payment process, and make it as easy as possible.
-  Help the customers all over the world discover products and manufacturers in China.
-  The Shortest order processed time and speed delivery