Safety Full Automatic Electric Opening AAC Autoclave For AAC Plant

Electric Opening AAC Autoclave ?AAC Block Making Machine ?Full Automatic Autoclave

1. Full Automatic Autoclave Product?Description:

The main product is?autoclave?aerated concrete block,?it?is the core?equipment of production line.?Once the failure?will cause?the embryo?out of kettle?and equipment?can’t operate?substandard?conditions,?so the?safe?operation?is extremely important.?Autoclave?is the hydration reaction?of?silicate products,?the main equipment?to obtain?the physical and mechanical properties.?The?operation?used in?aerated concrete block?production is the main content of?relationship between?production safety and?energy utilization.

2. Autoclave structure

The main parts of autoclave are autoclave door ,body apparatus, tank cover device, the door swing device, hand reducer, safety interlocks, bearings, insulation,,sealing devices, plumbing valves and meters, etc., also attached with drainage and electric control devices. Various structural designs and manufacturing can be safe and reliable, also can ensure the autoclave more stable in performance.

3. The safe operation of?steam?autoclave details:

Autoclave?operation is simple,?but very?important,?the operation process?is generally?good, both inside and outside the?rail?bridge?connecting?kettle,?the car?pulled into the?kettle,?kettle and check the?ends of?parking position?properly,?the withdrawal of?the bridge,?close the?kettle door?(in the pot?ring?coated with graphite?lubricant,?inflate?the seal,?should be?closed?before then?the vacuum,?by?heating,?cooling,?air?curing?temperature,?finally?open the door to a?kettle. Autoclave?in operation?should pay attention to the following points:

3. 1. The?safety valve

The safety valve is?in the autoclave?pressure?exceeds the limit,?the automatic unloading components,?therefore,?as the?pressure vessel?autoclave?should be equipped with?more than two?safety valves,?so that?when a?failure of?the other one still?use.?Safety valve?opening pressure?should be?rated?according to the?allowable working pressure?autoclave?to adjust, should be slightly lower than the?allowable pressure?value,?in order to ensure the?good performance of?the safety valve?must be?regular maintenance?and?daily?maintenance work.

3. 2.?The?kettle door?switch

The products into the?kettle,?should?carefully manage?the cauldron gate,?is?in?engagement with the?kettle?kettle door?ring,?and pull down?the?safety.?In the?air?before checking?kettle door closed.?Complete?the maintenance,?before opening?the kettle door?must pay attention to whether there is?pressure?vessel?inspection,?and the first?to?open the safe,?put?the residual gas?after?open the kettle?door,?and pay attention to?avoid?the operator?facing the?cauldron gate,?in order to prevent?the high temperature waste heat?burns.

3. 3. The?sealing ring

Between the?door and the?kettle?kettle?ring for?sealing ring?is a rubber product?in each?reactor closed?door?should be?in the pot?ring?doped?graphite?coating?lubricant?to reduce?friction?of the sealing ring?of?the kettle door,?at the same time,?also?can prolong?the service life of the sealing ring,?the sealing ring?is in use,?should be?regularly?check,?timely replacement,?to ensure effective?sealing?kettle door.

3. 4. Keep?the?water?clear

The autoclaved?kettle body?in addition?to bear?load?caused by?the formation of?the?steam pressure,?load?and?bearing?in the bearing?rail?pivot and the?kettle body?on the?autoclave?and the weight of?the steam car?and?the weight of the products?formed.?The?condensed water caused by the?top?and?bottom?temperature difference of?formation?stress,?autoclave?in the long-term?stress?of?this cycle,?easy?to form the?material fatigue,?thus losing?strength.?At the same time,?the corrosion?of water and gas also easy to make?the decrease of tensile strength.?Therefore,?we should?promptly discharge the?condensed water?in the use process, especially in the?initial stage of?heating?(30 ~60)?a large amount of condensed water?in the kettle,?if not timely?discharge,?will be in the?bottom?to?bottom?lower?aggregation,?forming a?low temperature region,?the?temperature difference?increases?(like?a?kettle body?in?10?DEG C) may reach?60~70 degrees),?the formation of?the kettle?on?under?too much?stress?