Non-invasive And Painless HIFU Vaginal Tightening Portable High Frequency Face Machine Machine For Vaginal Contraction Eyes Wrinkle Removal

 Parameters of Instrument 

Icons of System Interface

3D Operational Procedure (Users normally operate this system.)

1. Connect operational handle and wiring controller or pedal to the instrument. It is shown in the figure.

2. Take the detector out from cylinder and install it in the instrument. The detector's scale shall point at the handle

3. Plug in and turn the instrument on. The system will automatically enter into the operating tutorial interface. Carefully read the operating tutorial and enter into the following interface:

4. Clean your hands with clear water. Sterilize your hands with iodine or alcohol.

5. Clean the handle and detector of instrument with medical alcohol, as the figure shows. The part with arrow must be sterilized with medical alcohol or iodine. (Alcohol or iodine is inflammable products. Express delivery is not available, so we do not prepare it for customers. You can buy it in the pharmacy.)

HIFU Treatment Scope:

1. Remove wrinkles on around forehead, eyes, mouth, etc.

2. Lift and tighten both cheeks skin.

3. Improve skin elasticity and shaping contour.

4. Improve jaw line, reducing “marionette lines”

5. Tighten the skin tissue on forehead, lifting the eyebrows lines.

6. Improve skin complexion, making the skin delicate and bright

7. Match with injecting beauty like Hyaluronic acid, collagen, to resolve more aging problem

8. Remove neck wrinkles, protecting neck aging.

6. Immerse silicon case into iodine or alcohol for disinfection. After that, cover the silicon case on the operating handle, as the figure shows:

7. Sterilize the vulva with medical cotton swab with iodine or alcohol. The sterilizing method is to wipe the vulva from up to down, from inside to outside with a single cotton swab. If sterilization is needed again, please use another cotton swab with iodine or alcohol. Then clean vulva with the lotion for nursing care we send you

as the figure 5 shows 

8. On the display screen, adjust the length of operating head based on the length of your own vagina. (When the length on the screen displays 0, it means the length of operating head is 80mm. The larger the figure on the screen is, the shorter the operational head should be. Vice versa.)

9. Open the specialized glue for the instrument. Cover evenly the operating head with glue for the thickness of 1-2mm, which is shown as the figure.

10. Put condom on the operating head. We do not provide condom, so you shall use thick condom without spiral or salient point, which is shown in the figure.

11. Smear body lubricating oil on the condom. Decide the drops as your preference, generally, three drops are enough.

12. Measure the length of your vagina. (Jump over the step if it is your second or more operation.)

Put the operating head in vagina till the end. Check the scale on the operating head and get the length of your vagina. Then write it down on for the next operation.

13. Fix the band across your waist and put the operating head in the vagina. Hook the hooks on two ends of the band on the operating handle, which is shown in the figure.

14. Adjust the parameters on the display screen.

1. There are two operation times for selection, one is 15min the other is 25min. The instrument will distribute 1440 energy points in the whole vagina uniformly within 15 minutes if you select 15 minutes. The instrument will distribute 1440 energy points in the whole vagina uniformly within 25 minutes if you select 25 minutes. 

2. Selection of vibration strength. 0 represents no vibration, 1-4 represents the level of vibration strength, strength-1 is suggested for the first time. Vibration strength can be selected according to your bearing strength for the second and next operations. 

3. It is suggested to start from energy strength 3, the energy strength can be slowly ascended according as your feeling after starting operation. (The energy strength cannot be adjusted during operation, and the energy strength can be adjusted by pressing the pause key on the remote control or stamping the pedal to pause the operation) The energy strength can be adjusted by the remote control during operation and you can select the energy according to the bearing ability. It is strictly forbidden to selecting the maximum energy from the beginning and error operation shall result in unknown injuries. 

4. There are two selections for point number in one circle. One is 24 and the other is 36. It is suggested to selecting 24 for the beginning. The 24 refers to the point number of the operation handle circles 360 degrees in the vagina is 24 energy points. 36 refer to the point number of the operating head circles 360 degrees in the vagina is 36 energy points. (In theory, the dense of the energy point, the better effect of the dense effect is and the stronger feeling is) 

5. The user shall select the suitable age operation according to the actual age for the energy strength output in different age sections are different. Random selections are prohibited. (As the figure shows)

15. After the parameter is adjusted, press the preparation button on the screen. After that, the operating head will scan automatically. The scan display area on the screen will show the constant working of the scanning function. Then put the operating head into the vagina, you should lay on the bed or sofa, press the start button on the remote control and the detector begins working.

16. After the operation, take out and abandon the condom. Then pulled out the operating head and disinfect it with ethyl alcohol/iodine. Clean the detector with tissue after the disinfection. Then put it into and seal the cylinder.