1500cps high viscosity super glue cyanoacrylate instant adhesive for mdf kit in 20g

PRODUCT TECHNICAL DATA SHEET

GW-01

Rubber, Plastic & Metal

1. 1.  PRODUCT DESCRIPTION

GW-01 is a general-purpose industrial grade Cyanoacrylate adhesive with fast setting, high flow ability, and good penetration characteristics. It has been specially formulated to achieve the strongest possible bond between well-mated, non-porous surfaces, such as rubber, metals, plastics, etc. GW-01 is a one-component, solvent-free system and does not require the use of a catalyst, heat or clamps. When a thin layer of GW-01applied between two surfaces comes into contact with atmospheric moisture, a rapid polymerization occurs producing the ultimate bond.

1. 2.  TYPICAL PROPERTIES OF UNCURED MATERIAL

1. 3.  CURING PERFORMANCE

There are many factors that can influence the rate of cure. These include: the types of substrate used, the condition of the surface to be bonded, the smoothness of the surface, the closeness of the surfaces, the atmospheric conditions etc.

Cure Speed / substrate

Cure Speed / Humidity

The following graph shows the tensile strength developed at different levels of humidity.

Cure Speed / Bond Gap

The rate of cure depends on the bond-gap. A smaller bond-gap results in faster the cure speed.

1. 4.  TYPICAL PROPERTIES OF CURED MATERIAL

1. 5.  ADHESIVE PERFORMANCE

After 24 hours at 25ºC.

1. 6.  DIRECTIONS FOR USE
   1. 1.   Make sure the surfaces to be bonded are clean and dry (preferable to solvent-wipe plastics, glass, and rubber, and to              acid-treat metals).      
   2. 2.   Dispense a drop or drops to one surface only. Apply only enough to leave a thin film after compression.
   3. 3.   Press parts together and hold firmly for a few seconds. Good contact is essential. An adequate bond develops in less      than one minute. (Maximum strength is achieved in 24 to 48 hours).
   4. 4.   Wipe off excess adhesive from the top of the container and recapGW-01 if left uncapped, may deteriorate by contamination from moisture in the air.
   5. 5.   Because GW-01 condenses by polymerization, sometimes whitening will occur on the surface of the container or the bonded materials. Should this happen, wipe surfaces well with acetone.

1. 7.  HANDLING AND STORAGE

Storage:             Keep products in the unopened container in a cool and dry location. Best when stored at 2 to 8ºC. Temperatures less than 2ºC can adversely affect product properties. Do Not Freeze. Keep container tightly closed until ready for use.

Handling:        Material removed from containers may be contaminated during use. Do not pour back any product to the original container. Misuse of product will void all warrantees.

1. 8.  PRECAUTIONS
2. 1.  Use with proper ventilation. Avoid contact with skin and eyes.
3. 2.  If contact with skin occurs, rinse with warm water or dissolve gradually with solvent such as acetone, or nitromethane. Do not try to remove forcibly.
4. 3.  If adhesive gets into eye, keep eye open and rinse thoroughly. Seek medical attention immediately.
5. 4.  Keep well out of reach of children.
6. 5.  Keep adhesive in a cool, dry place 20-25ºC (68-77^oF). For long-term storage, refrigeration (2^oC or 35^oF) is recommended.

Disclaimer: The data contained herein are furnished for informational purposes only and are believed to be reliable. However, Nanpao Chemical Adhesive Company Limited does not assume responsibility for any results obtained by persons over whose methods Nanpao Chemical Company Limited has no control. It is the user’s responsibility to determine the suitability of Nanpao Chemical’s products or any production methods mentioned herein for a particular purpose, and to adopt such precautions as may be advisable for the protection of property and persons against any hazards that may be involved in the handling and use of any Nanpao Chemical Company Ltd’s products.Nanpao Chemical Company Limited specifically disclaims all warranties express or implied, including warranties of salability and suitability for a particular purpose arising from sale or use of Nanpao Chemical Company Ltd’s products. Nanpao Chemical further disclaims any liability for consequential or incremental damages of any kind including lost profits.

Revision Date:    May 05, 2015                                                           Revision:        0005