Hantek Handheld Isolated Oscilloscope DSO1062S 60MHz

Model

DSO1202S

DSO1122S

DSO1062S

                                            Oscilloscope Mode

Vertical

Bandwidth

200MHz

120MHz

60MHz

Real-time Sample Rate

1GSa/s

Equivalent Sample Rate

25GSa/s

Record Length (Sample Points)

Single-channel: Maximum 2M; Dual-channel: Maximum 1M

SEC/DIV Range 

2nS/div-2000S/div (in a 2, 4, 8 sequence) 

A/D Converter 

8-bit resolution 

VOLTS/DIV Range 

2mV/div~5V/div at input BNC 

Position Range 

+-50V(5V/div), +-40V(2V/div~500mV/div), +-2V(200mV/div~50mV/div)+-400mV(20mV/div~2mV/div) 

Rise Time at BNC

       ≤1.7ns

        ≤2.9ns

     ≤5.8ns

DC Gain Accuracy 

+-4% for Sample or Average acquisition mode, 5mV/div to 2mV/div

+-3% for Sample or Average acquisition mode, 5V/div to 10mV/div 

Trigger

Trigger Sensitivity
(Edge Trigger Type) 

DC: CH1/CH2(Typical) 1div from DC to 10MHz;1.5div from 10MHz to Full
AC: Attenuates signals below 10Hz

HF Reject: Attenuates signals above 80kHz

LF Reject: Attenuates signals below 150kHz

Noise Reject: Reduces trigger sensitivity 

Trigger LevelRange

CH1,CH2:+-8 divisions from center of screen

Hold off Range

100ns-10s

Trigger Level Accuracy,typical (Accuracy is for signals having rise and fall times >=20ns)

CH1,CH2:+-(0.3div×V/div) (within +-4 divisions from center of screen)



 

Trigger Type

Edge

Trigger on the rising or falling edge

Video

Trigger on an NTSC, PAL, or SECAM standard video signal
Line Range: 1-525 (NTSC), 1-625 (PAL/SECAM)

Slope

Trigger (when >,<,=,not equal) on a positive or negative slope
Set Time: 20ns-10s

Overtime

From the rising or falling edge
Set Time: 20ns-10s

Alternate

Internal trigger on edge, pulse width, video or slope

Measurement

Cursors 

Manual: The difference between voltage cursors deltaV; the difference between time cursors deltaT; 1/deltaT calculated by Hz.
Tracing: The voltage and time at a waveform point

Automatic 

Pk-Pk, Max, Min, Mean, Cyc RMS, Frequency, Period, Rise Time, Fall Time, Positive Width, Negative Width

            Meter mode

Max. Resolution

6,000 Counts

DMM Testing Modes

Voltage, Current, Resistance, Capacitance, Diode & Continuity

Max. Input Current

AC: 10A, DC: 10A

Input Impedance

10 MΩ

Isolation

The float voltage between BNC and Ground

600V CATIII, 1000V CAT II

The float voltage between each Channel

600V CATIII, 1000V CAT II

The float voltage between Multimeter and Ground

1000V

between input Ports directly

400V CAT II

Input by 10:1 probe

600V CATIII, 1000V CAT II

The Max input voltage of Multimeter

The float voltage between Multimeter and Ground

Display

Type

Right angle 5.6'' 16-digit color LCD

Resolution

640x480 dots

Contrast

16 gears, with the progress bar to show adjustment

Interface

USB host and USB slave, LAN Optional

Power

Voltage

DC Input:12--17VDC, 2000mA

Measurement

Size

245 x 163 x 52 (mm)

Weight

3.5kg