Manufacture Scrap Copper Wire Recycling Granulator Machine For Sale

Introduction of Copper Wire Recycling Machine:

This machine also called scrap electric wire and cable recycling equipment, copper wire separator, aluminium wire separator or electric wire reparator.Copper Wire Recycling Machineis a kind of environmental protection machine used to recyle waste electric wire, copper wire, aluminium wire, metallic composite wires and sheathed lines.

Through crude crushing,  iron removal, fine crushing,  gravity separation, electrostatic separation process to make completely dry and physical separation of scrap wires to get pure plastics and metal for double recycling and high benefit. Equipped with the electrostatic separator, it can make metal recovery rate get close to 100%.

This copper wire crusher is a compact plant, assembled with a blade mill for chopping the cables and an air separating system to produce the clean copper granules. 

Specification of copper cable wire recycling granulator machine:

Advantage of Copper Wire Recycling Machine:

1. This machine is of high efficiency, the purity rate of copper granules can reach up to 99%. 

2. Labor and cost saving, it is a complete solution for processing scrap copper wires.       

3. No air pollution and no water is used for separation and there is no air pollution. 

4. It is an installed all-in-one machine; the customer only need to connect it to power and it works. It is also easy to move and transport. 

5. Easy to operate and maintain. Small working site is available.

Technically advanced copper rice machine treatment of waste cable effect is very good, waste cable after a series of processing means, you can get pure copper particles and plastic. The so-called copper rice, is the copper particles, the quality of the equivalent of electrolytic copper quality, can be directly used.

Process of Copper Wire Recycling Machine:
1. Pre-shredding
 Shred the cables prior to granulating.
2. Crushing 
Crusher, an important part before separation, used to shred the materials into 3-5mm smaller pieces.
3. Copper and plastic separation and dust collecting system
The whole process mainly adopts air separation assisted by vibrating separation. A specially designed dust collecting system will be used to collect all the dust caused.

Working principle of Copper Wire Recycling Machine:

1. Feed scrap copper wires into the chopper; 

2. Chopped wires are transported to vibrating system for separation; 

3. Copper granules and insulation granules are separated by vibrating and air separation. 

Materials of Copper Wire Recycling Machine: 

1.    Copper cable and wire;
2.    Aluminum cable and wire;
3.    Auto wiring harnesses;
4.    Communication cables;
5.    Household electric wire;
6.    Computer wire;
7.    Other unclassified cables which cannot be processed by wire-stripping machine.

Key component:
Pre-shredder, material conveyors, crusher, copper separating system, dust collecting system, etc. 

Features of Copper Wire Recycling Machine:
1. It can process cable and wires where single core, double core or multi-core, either twisted or tangled, with or without plug. The max Dia. for double core and multi-core cables is 20mm. For
single core wire, the minimum Dia. should be 0.2mm.
2. The shredder can rotate reversely when blocking. When crusher is over current, the conveyor will stop automatically.
3. Main parts will be connected together by screw conveyor, so it will be very easy to maintain.
4. This machine adopts air and vibrating separation in dry processing mode equipped with dust collecting system.
5. The machine is controlled by the most advanced PLC control system with pressing Start and Stop button.
6. Blades can be reground again and again. If used correctly, their service life can be at least half a year or more.

 Details of Copper Wire Recycling Machine:

 ♦ Pre-sale Service

(1) According to the customers' special requirements, provide the most suitable project design, process design and the purchase program.

(2) Guide customers to choose the best and economical plant, recover investment within short time, and site inspection.

♦ On sale service

(1) Welcome you to our factory for a visiting;

(2) Accompany you to check our machine production, quality and  the working conditions.

(3) Customize the equipments strictly according to your special requirements and arrange the timely delivery.

♦ After-sale service

(1) Installation guidance

When the machine arrives at your company, we will dispatch our technicians to your factory to guide the installation and commissioning at site.

(2) Technical training

We provide free technical training service to your stuff. Training content contains the main work principle of machine, operating regulations, maintenance methods and steps, safety, etc.

(3) Warranty

Three guarantees of our product quality, warranty for one year (not include man-made damaged). We will maintain the machine for free for the quality problem. If the damage is caused by your improperly operation, the cost of the maintenance burden by you. we also provide you the  life-long follow-up service.

1. Are you manufacturer or trade compnay ?
We are the manufacturer, which have more than 10 years experience specialized in all kinds of waste recycling machinery.
2. How does your factory do regarding quality control ?
Quality is priority, since establishement, we keep strictly requirements about the quality with using X-Ray to test every section of the products, so we gain high praise  from our customers ,all product have to pass strict inspection before they were sent out.
3. How about your after-service ?
We will provide one year free warranty for our machine, and after machine delivery, we have the engineers which can be sent to your site for machine installation, commissioning and traning your workers. You also can feel free to contact us, when you have any questions about our machine. 

Copper Wire Recycling Machine