Description:
ATU-130 is a 150w automatic antenna tuner. Improved on the basis of ATU-100 hardware, it is an universal type.

Features:
- Adopt PIC18F2520, MCU
- Using 4pcs T94 magnetic ring inductors, the coil above 1mm, the withstand power is greater, and the heat is much smaller than the original one
- Use HF32, 10A, HF33, 5A relays (similar to that for icom at130)
- Adopt 6KV high-voltage capacitor with low loss
- Miniature shortwave automatic antenna tuner

Parameters:
- Coverage frequency: 3.5-54MHz
- Tuning impedance range: 5Ω-1.2KΩ
- Tuning power: 5-15W
- Transmit power: SSB 160w max
- Maximum measurable power: 180w
- When the initial standing wave deviation is large, it is recommended to use the SSB not more than 150w for a long time. (FT8, AM, FM, CW is not more than 100W. When the deviation of the standing wave before adjustment is large, reduce the power as appropriate)
- Size: 38 x 88 x 155mm/1.5 x 3.5 x 6.1" (without the size of protrusions)
- Power supply: 11-14VDC power supply

Package Included:
- 1 x Set of Antenna Tuner

Instructions:
- Connect the power cord to 11-14vDC power supply. Connect a shortwave radio to the IN RF line of the automatic tuner. The antenna is connected to the ANT of the antenna tuner (M seat or quick socket). With Am, fm, cw 6-15w well tuned (within swr1.5), you can use high power.
- If the standing wave is too large and the tuning is not successful, high-power transmission cannot be used, because it may damage the antenna tuner or shortwave radio. Please remove the fault and then transmit with high power.
- Good grounding is good for standing wave tuning. If it is unconditionally grounded, connect the grounding end of the tuner to the grounding of shortwave radios.

Attention:
- The product defaults to automatic mode.
- If manual operation is required, you can press auto once, the small dot in the middle of the screen LC disappears, and the instrument is in manual mode. Press it again to switch to automatic mode. In special cases, after pressing tune to reset, the LC combination is set to zero.

Package: Normally we use the standard exporting packaging. We also can according to clients' request .

 Shipping : 

1. By Couriers: DHL, UPS, FEDEX, TNT are the main courier  we are co-operating at present.

2. By Air: Delivery from the Shanghai airport to customers’ destination city air port.

3. By Sea: Delivery from the Shanghai sea port .

Q1. Can I have a sample order?

A: Yes, we welcome sample order to test and check quality.

Q2. What about the lead time?

A: Samples arrived often need 3-5 days.

Q3. Do you have any MOQ (minimum order quality)limit?

A: Low MOQ, 1pc for sample checking is available.

Q4. How do you ship the goods and how long does it take to arrive?

A: We often ship by DHL, UPS, FedEx or TNT. It usually takes 3-5 days to arrive. Airline and sea shipping is also optional.

Q5. How to proceed an order?

A: Initially, let us know your requirements or application. Besides, We quote according to your requirements or our suggestions. Thirdly, customers confirms the samples and places deposit for formal order. Finally, We arrange the production.

Q6. Is it acceptable to print my logo on the product?

A: Yes. Please inform us formally before our product and confirm the design firstly based on our sample.

Q7: Do you offer guarantee for the products?

A: Yes, we offer one-year warranty for our products.

Q8: How to deal with the flaw?

A: Our products are produced in strict quality control system and the percent of pass is often maintained over 99.8%

Please do not hesitate to contact me if you need any further information

Whatsapp/Tel/Wechat: 8619902906050

Web: 

Address: Room 303 Building 2,Youpin Cultural and Creative Park,Zhangkeng,Minzhi Street,Longhua District,518131,Shenzhen,China(Mainland)