PortaPack H2 + HackRF One SDR + 0.5ppm GPS TCXO + Havoc Firmware + 3.2 Inch LCD Display

Description:
The official firmware created for the PortaPack has several decoders and transmitters built into it, but the third party 'Havoc' firmware is really what you'll want to use with it since it contains many more decoders and transmit options.

Progress of Work:
1. It has completed the program validation prototype.
2. The latest 2017.5 month documents are based on improvements.

Capture and Replay:
-One of the best things about the PortaPack is that it makes capture and replay of wireless signals like those from ISM band remote controls extremely easy.
-To create a capture you just need to enter the "Capture" menu, set the frequency of the remote key, press the red 'R' Record button and then press the key on the remote.
-Then stop the recording to save it to the SD Card.
-Now you can go into the Replay menu, select the file that you just  recorded and hit play. The exact same signal will be transmitted over the air,  effectively replacing your remote key.

Microphone TX:
-Using the 3.5mm audio jack the Portapack can also be used as a standard  Push to Talk or voice activated walkie talkie radio. With a microphone plugged  into the audio
jack simply hold down the right button to push to talk.
-If required you can also enable multiple CTCSS tone options, as well as tones that look like they enable transmission to wireless headphones

Other Transmitters:
-There are generic OOK transmitter which can be programmed with custom data. This mode might be useful for experimenting with simple keyfobs, or things like home.
automatation switches.
-There are numerous transmit modes implemented that are questionable in most countries and could get you into huge trouble. These transmitters are purely to be used for internal testing with a faraday cage!

Receivers:
By connecting speakers to the Portapack's 3.5mm audio jack you can easily listen in on standard NFM and WFM  audio signals. ADS-B reception can be easily  enabled on the
PortaPack by selecting the inductor and lightning symbol on the  top right. With the bias tee enabled you can receive aircraft.

Hardware Configuration:
-3.2 inch TFT240*320 screen
-Navigation switch
-Audio output
-Microphone input
-DC 2.1 interface
-4 layer gold plate
-ROSH process (exported to Europe and America)

The latest version is updated with the latest documents in 2017.5 month

Add a PortaPack  to your HackRF One software-defined radio, and leave your laptop behind! The PortaPack  attaches to your HackRF and adds a touchscreen LCD, navigation controls,
headphone jack, real-time clock, micro SD card slot,

Just add a USB battery, and you're ready to explore radio spectrum wherever you are. The PortaPack firmware runs on the fast ARM processors in your HackRF. No computer is necessary
(except for reprogramming firmware).

HAVOC Features Include:
-IQ file replay
-Microphone FM transmit with CTCSS
-CTCSS decoder
-Frequency manager (save & load from SD card, with categories and notes)
-File manager
-"Soundboard" wave file player (put 8-bit mono files in SD card /wav directory)
-ADS-B receiver with map view
-SSTV transmitter
-Fully configurable transmit signals
-POCSAG transmitter
-POCSAG receiver/decoder
-Morse transmitter (FM tone and CW)
-OOK transmitter for common remote encoders (PT2262, doorbells, remote outlets, some garage doors, ...)
-RDS (Radio Data System) PSN, RadioText and Time groups transmitter
-Meteorological radiosonde receiver for M10 and M2K2...
-AFSK receiver
-AFSK transmitter (Bell202...)
-Nuoptix DTMF sync transmitter
-TouchTunes jukebox universal remote
-LCR (Language de Commande Routier) message generator
-Street lighting control transmitter (CCIR tones)
-"Play Dead" in case of emergency
-Fully configurable RF signal generator
-RSSI audio output as pitch (for direction finding)

Features:
-3.2 inch, 240 x 320 RGB LCD with resistive touch panel.
-Four-way arrow keys, rotary jog wheel, and select button.
-Coin battery for preserving settings and date/time.
-Micro SD card slot for data and code storage
-Some features demonstrated in 2016 February 22 firmware video:
-SSB, AM, narrowband FM, wideband FM audio reception, with spectrum waterfall.
-Wideband (18MHz) spectrum analysis and waterfall.
-Monitoring of boat (AIS), automobile (TPMS), and utility meter transponders (ITRON ERT).
-HackRF mode runs HackRF firmware for use with host computer SDR software.
-PPM calibration for more accurate tuning.
-Sleep mode saves power by turning off just the display.
-You may also find the Furrtek HAVOC firmware very interesting!

Note: Some assembly is required.

Your HackRF will continue to function with computer-based SDR software, when you put the PortaPack into "HackRF Mode".

PortaPack is compatible only with the HackRF One. It is not compatible with the earlier HackRF Jawbreaker design. If you have an RF shield installed on your HackRF,
the PortaPack should fit just fine. Compatibility with the HackRF Blue is experimental. One Blue owner has reported good results with minor mechanical interference
between the PortaPack audio capacitors and the baseband header. If your HackRF Blue does not have a baseband header installed, you should have no mechanical problems.

PortaPack  requires an external battery. Any USB-connected battery should work, though they vary widely in quality and poorly-designed batteries may inject voltage regulator noise into the radio.

The PortaPack and HackRF One will not replace your handheld ham radio receiver. Receive sensitivity varies from band to band, but will not perform as well as a true ham radio receive

Package List:
-1 x Portapack with 3.2-inch Touch LCD
(Havoc Firmware Preinstalled)
-1 x HackRF One
-1 x Antenna
-1 x 1500mA Battery

Detail photo

FAQ 

Q1. Can I have a sample order?

A: Yes, we welcome sample order to test and check quality.

Q2. What about the lead time?

A: Samples arrived often need 3-5 days.

Q3. Do you have any MOQ (minimum order quality)limit?

A: Low MOQ, 1pc for sample checking is available.

Q4. How do you ship the goods and how long does it take to arrive?

A: We often ship by DHL, UPS, FedEx or TNT. It usually takes 3-5 days to arrive. Airline and sea shipping is also optional.

Q5. How to proceed an order?

A: Initially, let us know your requirements or application. Besides, We quote according to your requirements or our suggestions. Thirdly, customers confirms the samples and places deposit for formal order. Finally, We arrange the production.

Q6. Is it acceptable to print my logo on the product?

A: Yes. Please inform us formally before our product and confirm the design firstly based on our sample.

Q7: Do you offer guarantee for the products?

A: Yes, we offer one-year warranty for our products.

Q8: How to deal with the flaw?

A: Our products are produced in strict quality control system and the percent of pass is often maintained over 99.8%

Packing&Shipping

Package: Normally we use the standard exporting packaging. We also can according to clients' request .

 Shipping : 

1. By Couriers: DHL, UPS, FEDEX, TNT are the main courier  we are co-operating at present.

2. By Air: Delivery from the Shanghai airport to customers’ destination city air port.

3. By Sea: Delivery from the Shanghai sea port .

Company information

TZT has been speciliazing in Business & Industry,Hobbies & Toys,CNC Products and Health care supplies for over 5 years.We committed to enhance customer satisfaction by continually improving the process with a vision of expertise in the field. 
Aiming to provide high quanlity products and great service for buyer,we are strict on product quanlity control and offer instant communication service.Welcome to contact us!

Our Advantages:
-  Source only the best consumer goods and ensure the highest quality.
-  Streamline the buying and payment process, and make it as easy as possible.
-  Help the customers all over the world discover products and manufacturers in China.
-  The Shortest order processed time and speed delivery