automatic High plastic welding machine hot air welding machine pvc banner welder

 1. Introduction:Thank you very much for choosing our “Automatic TOP3400 Hot Air Welder”. We believe that this will be your best choice for your business. This equipment is designed professionally for seaming PE , PVC and painting banners.

2. General instruction for safety:

Warning: The basic principal of safe protection should be followed to reduce the danger of fire in disaster, electric shock and personal harm. Please pay attention to the following items carefully before operation.

1). Keep the working place clean. Messing up and the disorderly working place cause disaste

2). Choose the work place carefully and use the machine in a bright and dry circumstance.

3). The electricity, controlling box and protective facilities have to be in the proper order after finishing daily work. The electrical power supply has to be switched off definitely.

4). The machine has to be stopped before gets maintenance or replacing the parts.

5). Use standard or indicated tools when dismantling or replacing parts.

6). For safety and the long life of the machine, please do not let the machine operates overtime.

7). If any special incidents happened, please stop the machine first for repairing, And do not deal with the special incident with improper procedures.

8).  If the machine is operated on land, keep the work place clean and no dust there. If dust or something blocks the inhaling filter of heater, the heating wind can not come cut adequately and then temperature inside of filter will rise to let the heater burn down.

3. Moving,Dismantlement,Installation,Cleaning:

1). Any part of this machine being bumped of fallen can cause some damage impossible to be repaired.So please pay attention to carry it.It is suggested to move the machine by manpower and put it down carefully.

2). Please check if there is damage or missed parts after unpack the machine.Any problem, please contact us or the local agent immediately.

3). The place for installation must be flat and the floor is strong enough to support the machine and moreover, the installation place should close to power supply.

4). Keep the installation place no dust and avoiding sunshine.

5). Please sweep away the anti-rust oil from the machine with detergent and re-lubricate with light lubricating oil after installation.

4.Connecting the power supply:

Connecting the electric wire to the reserved plug(AC220V)of controlling box.

5. Operation:

1). Make the cloth for seaming flat and put it underneath.Fix both ends by adhesive tape or something else.

2). The overlap width of the two pieces is about 3-mm, the width of the nozzle of hot seaming machine.

3). Put the machine nozzle between two overlap pieces.The press-wheel should be at left side of nozzle.The nozzle also need align with side of upper piece of cloth.

4). Switch on the motor power and then adjust speed.

5). Turn on the movement switch.

6). Press heating power key to adjust temperature.

7) Turn the bar by anticlockwise to fix the position to startup automatic movement.The machine will go along with the overlap path by itself.

8).Turn the bar by clockwise to cease the automatic work.

9). The operator should control the moving direction and make sure the nozzle connect both with upper and under piece of cloth.

6. notice:

1). During operating, if the surface cloth is dissolved and scorched or the cloth are not sticked together, please stop to adjust the temperature or speed.

2). During operating,if the seaming part is not in right position, please stop to adjust fixing position.

3). During operating, make sure clothes are flat so that stick together smoothly

4). The hot wind of heater cannot touch the press-wheel or the rubber of press-wheel is easy to be burned down.

5). Adjust temperature to zero before turn off the heater.Switch off after 5-10 minutes.

7. Maintenance:

Take care the nozzle.Use brush to clean if there is dust or block in the nozzle or filter.

8. Specification:

Electric heating:3400W

Motor:15w

Voltage:220V/230V

Frequency:50/60HZ

Temperature scope:0-650 Degree

The thickness of material to be weld:0.2-2mm.

Welding Area:2-6cm

Welding speed: 1-15/min

Working Temperature:400degree(normally)

Specification: L:58cm, W:30cm, H:60cm

Net weight:22kgs

Gross Weight:28kgs

Packing size:54*42*42mm

Package: wooden case with carton outside

9. Advantage

Can overlap welding and belt welding

6cm Wide speed nozzle

Use Weldy heat gun from Leister factory in Shanghai, long use life

Has infrared position device

With long stick, no need keep kneel during welding

LED display, it’s good to operate in dark

Wooden export package, safe for deliver

Our promise:

All goods shipped are the same as described.

All goods are checked and qualified.

All enquiries and questions usually will answer within 12 hours.

We hope we will build up with all buyer the best and long term relationship due to our honesty,speed and the best services.