High Efficiency 36w U Shaped SMD LED Tube Light 2ft For Department Store / Showcase

? ? ? ? ? ? ? ? ? ?High Efficiency U Shaped smd Led Tube 2FT with UL cUL 5 Years Warranty

Specification of smd Led Tube

Characteristics

1.super?optical?benefits:
High brightness?120LM/w,80Ra,PFC>0.95,THD<10%,?and?high?illumination?up?to 70lux/3m height.

2.great?material?to make sure excellent?heat?dissipation?performance
our own mould:?good looking?outer design, deep strip ,easy for heat releasing Aluminum board and aluminum housing guarantee?double heat?releasing to?avoid light depreciation and prolong lifespan>50.000hours .?

3.??safe driver design:?isolated driver (internal and external available).

4.??LM80 test report?for Epistar 3528 led chip burn-in?in 6000hrs?,?LM79?parameter?test report for led tube

5.?Strict quality control:72hrs?burn-in?test?before?shipment,low?failure?rate?within?3‰.

A?series?of?testing?like?shaking?test,?low?and?high?temperature?test?(-25°C~?65°C),drop?test?from?the?height?of?90mm?in?8directions?,hipot?test?1500V?for?1?min?and?so?on.

24hrs?for?burn-in?light?source

24hrs-48hrs?for?burn-in?drivers?and?shorts

48hrs-72hrs?for?burn-in?leakage

48hrs-72hrs?for?burn-in?IC,compacitor?and?resistor

6.?5 years warranty?, under the warranty ,less than35% depreciation of light output compared with initial EXW?lumens, ?we are responsible for our clients?

Installation of smd Led Tube

Steps?1:?Turn?off?the?power?at?the?source?first

Steps?2:?Untwist?the?conventional?fluorescent?lamp?and?then?remove.?

Steps?3:?Cut?the?AC?Positive?Line?and?AC?Neutral?Line.

3.1?Bracket?with?inductive?ballast?

Open?the?diffuser?of?the?bracket(if?any).?Removing?the?starter?and?ballast?by?cutting?the?wires?according?to?picture?A.?And?Remove?the?

ballast?and?starter?from?lamp Fixture.

3.2?Bracket?with?electronic?ballast?Open?the?diffuser?of?the?bracket(if?any).?Removing?the?electronic?ballast?by?cutting?the?wires?according?

to?picture?A.?And?Remove the?electronic?ballast?from?lamp?fixture?

Steps?4:?Connect?the?AC?Postive?Line?and?AC?neutral?Line?to?the?input?side?of?the?external?driver.

4.1?Connect?the?AC?Neutral?Positive?Line?direct?to?the?white?wire(ACN)?from?the?driver?by?using?connection?caps?provided.?Then?connect?

the?AC?Positive?Line?to?the black?wire(ACL)?coming?from?the?same?driver?by?using?connection?caps?provided.?

Steps?5:?Connect?LED?fluorescent?lamp?to?external?driver?according?to?picture?A.????

Steps?6:?Install?the?LED?lamp?to?the?retrofitted?luminaries,?close?the?diffuser.

Steps?7:?Mount?the?clip?to?the?fixture.?Drill?three?holes(3?mm?diameter)?to?secured?the?clips?by?srcew?and?nut?on?the?lamp?fixture.

Steps?8:?install?the?metal?case?for?power?supply?protection

8.1?Put?the?power?supply?into?the?metal?box?and?then?fixed?to?the?lamp?box?with?screws?near?lamp.?

8.2?Open?two?little?holes?(the?diameter?about?4?mm)?near?the?lamp?for?fixing?the?protection?box.?The?protection?box?should?be?made?

of?steel?with?minimum?0.51mm?thick?to?fully?enclose?the?LED?Driver?and?should?not?have?any?open?holes.

8.3?After?modification?completes,?then?affix?the?Lamping?Replacement?Marking?label?and?cautionary?label?to?painted?surface?and?bare?

aluminum?,?located?this?where?visible?during?re-lamping?on?the?retrofitted?luminaire.

Application of smd Led Tube

1. use( living room, bedroom, kitchen, washroom )
2. School, University, Hospital, Hote
3. Conference, Meeting room, Show room, Showcase
4. Commercial Complexes
5. Factories, Plants, Wareho