PA nylon Plastic Blow Molding Machine

PA nylon Plastic Blow Molding Machine with 30L accumulator air tank?

Brief introduction

Features:

? 1. Structure design front and back is a complete set, no welding, heavy structure design make sure machine no any viberation when in production

? 2. Linear guide support the Carriage up down and clamping,reduce the friction between tie-bar and bushes,extend the life of machine.

? 3. Self-lubricated Copper bush used in all the moving point,make machine working more faster

and stable

? 4. Carriage up and down speed control valve installed,make sure machine working in high speed but no any noise and shake.

? 5. Linear transducer and stroke switch installed for better control and safety control

? 6. A return oil cycle design in the nose part of oil cylinder rod to avoid any leakage possibility

? 7. Automatic center lubrication system ,controller can set the lubrication time and frequency

? 8. Platform manually adjusted up and down,die head have twin-cylinder design

? 9. Fast response PLC control system, easy operating, endurable

? 10. Each hydraulic circuit can be controlled separately

? 11. 30L accumulator air tank installed for stable the blow air pressure and flow

? 12. Micro parison thickness adjustment along with micro blow pin center adjustment are controlled by 3-4bolt,easy for operator

? 13. Whole cooling system water pipe are using Oil pipe, longer life and remain low temperature? 14. Material loading gate and material level sensor is installed,can connect with auto-loader

? 15.Mould lifting crane is optional for easier mould installation

Machine specification:

MP80D-1T-5LAYER (70/70/35/35/25)

5Layer single head with View strip optional

(1). Extrusion unit

1. ?Main screw:70mm? with L/D:24/1 ?Screw RPM:15-60R.P.M

1) Heating zone:3zones?? Heating power:10.8KW

2) 2 Fan zones,Temperature can be individually controlled by PLC interface

3) extrusion motor size:18.5KW

4) Adopt Rexroth-Germany inverter ,size 18.5KW

5) Gearbox adopt top 3 China brand Yuyuan,model:ZLYJ-200

6) Main screw is using for the outer layer, thickness accounting 42.5%

2.? First layer screw:70mm with L/D:24/1 ?Screw RPM:15-60R.P.M

1) Heating zone:3zones?? Heating power:10.8KW

2) 2 Fan zones,Temperature can be individually controlled by PLC interface

3) Adopt Rexroth-Germany inverter ,size 18.5KW

4) Gearbox adopt top 3 China brand Yuyuan,model:ZLYJ-200

5) first layer after the outer layer,thickness accounting 42.5%

3. ?Adhensive screw:35mm with L/D:24/1 ?Screw RPM:15-60R.P.M

1) Heating zone:3zones?? Heating power::2.2KW

2) 1 Fan zones,Temperature can be individually controlled by PLC interface

3) Adopt Rexroth-Germany inverter ,size 2.2KW

4) Gear box using direct connection design more accurate and powerful

5) ?Adhensive located in Second and fourth layer,each layer thickness accounting:5%

4.? EVOH layer Screw diameter:35mm? L/D ratio:24/1 Screw RPM:15-60R.P.M

1) heating zone:3zones Heating power:2.2KW

2) 1 Fan zones,Temperature can be individually controlled by PLC interface

3) Adopt Rexroth-Germany inverter ,size 2.2KW

4) Gear box using direct connection design more accurate and powerful

5) EVOH between 2 layer adhensive ,accounting 5%

5．View strip screw size:25mm? L/D:24/1 Screw RPM:15-60R.P.M

1) heating zone:3zones Heating power:1.6KW

2) 1 Fan zones,Temperature can be individually controlled by PLC interface

(2) Die head

? 1. Number of Head:Single

? 2. Type:FIFO

? 3. Heating zone:3,heating power:10KW

? 4. Die (Thickness)adjustment:4 Bolt adjustment

? 5 ?Material:38CrMoAlA,Cr12MoV

? 6. Hydraulic cylinder diameter for MOOG:120mm,stroke:20mm

(3) Clamping unit

? 1 Mould height:465mm,Mould width:520mm

? 2. Platen stroke:220-620mm.

? 3. clamping foce:150KN(15Ton,140kgf/cm2)

? 4. Locking cylinder diameter:120mm??? stroke:450mm

? 5. carriage cylinder diameter: 50mm stroke:540mm

? 6. Carriage moving type:Tie-bar and linear.

? 7. Locking Supporting arm,Hook,Copper platen balance ring using for strengthing?

? 8. Self-lubricated Copper bush using for all the moving part

? 9. Planten width:420mm

? 10. Platen height:465mm

(4) Blowing unit

? 1. Blow pin oil cylinder diameter:40mm ?stroke:150mm

? 2. pre-b