2016 new promotion co2 laser power supply HY-DY13 For reci z4 s4 cuting and engraving machine

Reci DY13 Power supply

  DY13, The product is featured as small size, quick response, which is suitable for Reci S4  Z4  W4 laser glass  tube.

1.Specification:

DY13 Power Supply Instruction

I. Instruction for sub-connection wire of the controlled

1) Footer 1 is 5V power supply. (Not needed when connecting the cardinal plate.

It is used when regulating the power with potentiometer, and 5V current 

should be less than 10 mA.

2) TH. TL refers to high and low power level respectively, and WP refers to water

protection.

3) Footer 5 G refers to ground, and 6 refers to input end.

4)  When connecting the control plate, connect the light signal with footer2 in 

case of high power level light-emitting, (footer 3 for low power level

light emitting), connect the gwire with footer 5, connect footer 6 with

power control analog signal, and make short circuit for footer 4 and 5.
5) PWM can also be used in footer 6, but the pulse peak is required to reach 5V, and

 and the frequency should be above 20K.

6) For testing: 3, 4 and 5 are in short circuit (or 4, 5 are in short circuit and 3, 

5 are connected to switch), the potentiometer center is connected with 6 IN, and

the two other ends are connected to 5V and ground (1 and 5) respectively.

7) The high power level controls the light, 1 and 2 are connected, and 4 and 5 are in

 water protection.

8) It is not proposed to control laser power with high

frequency modulation, because it will have impact on the service life of the

laser.

9) The model is applicable to W4 laser, it is necessary to regulate and use the 

current 

according to the laser instructions.

10) The ammeter is concatenated to the cathode line.

II. Instruction for power wire

Note: The table 10A refers to the connection wire requirement, but not the actual 
power dissipation.

III. Instruction for laser connection wire

1) The positive red-line with high voltage is connected to the laser tail

2) The negative white-line is connected to laser output window

IV. Current limitation

To limit the working current, the potentiometer (lies in the underside of the power
supply) should be rotated in counterclockwise (please refer to the schematic diagram
. Limit the maximum output current as it is 
regulated in the operating instruction. The working current should be limited before
delivery.

V. Linear scale between input signal and the output current

Turn around the potentiometer, the linear scale will be changed: for example, when the
input signal is 0-5V, the output current is 0-34mA.Or when the input signal is 0-2V, the output signal is 0-34mA.

Note: when the potentiometer is turned down too much, the real output current will
be brought down by the same input signal. 

1. Packing  

 All Laser power will be packed in Wood case or Carton box avoiding to be damaged during the  shipping and we will make sure the best and  high-quality products for you.   

2.Shipping Policy

2.2 generally, we deliver the parcel in 3~5 days after your payment , But we will deliver the parcel by other Express in case quoted Express can’t reach your shipping address. 

2.3 We will ship to the  address which you leave to us  , when  you want to change address ,please inform us before the shipment  , otherwise we are not responsible for wrong or undeliverable address

2.4  We will choose the best way send the goods to you if the courier you chose it not good to Clearance.

2.5  We ship to worldwide but if your country's custom is strict, please contact us before you bid to check detail and confirmed.

2.6 .Please open the package and check if there are some damages before sign, if there are some damages , please do not sign and contact us immediately.

4.Payment Policy

4.1 We accept Online payment, also included western Union, Money gram, T/T etc.

4.2 Payment must be made within 48hours of the auction end time

Shenzhen Reliable Electromechanical Technology Company is a professional laser equipment supplier, committed to the R&D, production and sales of laser marking machine, laser cutting machines and laser engraving machines, as well as laser equipment parts.

24 hours   after sell service  by email or whatsapp   on line