Poultry Breeder House/ Chain Feeding System

Made of high quality galvanized sheet, hopper and trough interface site has a cover plate, it is easy to adjust the height of material level and prevent feed spill.

Trough made of wear-risistant and anti-rust material, have 44mm width of limited food grill, which can separate the hens and roosters apart effectively, and different width food grill can be customized according to customer requirements.

Hot galvanizing process, anti-corrosion, more suitable for poultry house environment.

Its surface are special hardening processed, alloy bearing don't need oiling, have good wear resistance and long service life.

Power: 0.75kw

Voltage: 380V/220V/customerized

Frequency:50hz, three phase/single-phase, AC current.

Size: 70Kg, 90Kg

Material: hot-dip galvanized sheet, thickness: 1mm

Material: Hot-dip galvanized steel pipe(the zinc coating amount is more than 275g/m2), thickness:1.2mm

Diameter: 45mm

Specification: 4 holes/3 metres, 3 holes/3 metres

Origin: imported from South Africa

Feeding ability: 400kg/h.

The sensor is installed inside feed pan(connect to open), driving motor starts working to convey feed when sensor doesn't touch feed, driving motor will stop working when sensor touchs feed. 

When feed sensor is installed at the bottom of feed bin(connect to close), the function is opossite to the above situation.

1). Feed pan diameter: 360mm;

2). Material:pp---Polypropylene;

3). Feeding capacity: 12.5 birds/pan;

4). 16 grills width of 40-52mm divide into 11 files, suitable for all stages breeders (including day-old birds) feeding needs;

5). Feed hole height of 70mm,80mm,90mm three files. when feed hole width is 52mm, height is 80mm, chicks can in&out freely;

6). Feed pan capaicty: 16 grades files, 200-630g/pan, which can meet different stages chickens eating demands;

7). Pull switch design, easy to switch each pan;

8). Bottom of the pan can be hanged, easy to take down, convenient to install and wash.

1). Feed pan diameter: 360mm;

2). Material:pp---Polypropylene;

3). Feeding capacity: 8-9 birds/pan;

4). With 9 grilles design, there are still intake hole after supplementing male breeders.

5). The fixation clamp can prevent feed pan swinging, so as to keep feed at the center of feed pan.

6). The adjusting ring at the top of feed pan can adjust the feed gears to the optumum position to reduce the waste of feed. 

Front part is controller of water, usually installed in control room.

1). Pressure regulator: make sure to supply stable water to drinking line. Anti-backlash device can discharge the impurity in pipe.

2). Filter: clean water and avoid blocking nipples.

3). Water meter: measure water usage volume.

4). Doser: add medicine exactly to prevent disease automatically.

1). Outside shell of nipples is made of pure engineering plastic, inner valve rod is made of stainless steel.

2). Feeding capability: 8-10 birds/drinker.

3). All nipples are anti-rusting, service life over 10 years.

4). Nipples have double-sealing structure, with good seal ability, avoid water leakage and its bad influence to chicken house.

5). Nipple's valve rod is movable in 360 degree, it's suitable for all chickens to drink, from day-old chicks to adult chickens.

1). Good regulating stability, high switching performance.

2). Sufficient water supply.

3). Recoil cleaning with good cleaning result, save time& water.

4). Good quality movable valve, easy to change

Use high transparency& impact resistant meterial, it's sturdy and durable, easy to watch water level, easy to take down and clean with this advanced design.

3T-20T silo (galvanized steel sheet)

600Kg/ 800Kg manpower hopper

Noted that usually breeders are hungry breeding, you need to control the feed consume.

Power: 0.75Kw; 

Voltage: 380V/220V/customized, Three-phase/Single-phase;

Frequency: 50Hz

Diamater of conveying pipe: Φ75mm;

Material:PVC

Origin: imported from South Africa; 

Feed ability:1400Kg/h;

Conveying length:60m

Diameter: 75mm

Material: plastic