Wooden Bucket Health Care Foot Sauna MY828

Specifications

Far foot sauna

Knowledge of far infrared ray

An infrared sauna is usually a wooden box, or small wooden room, containing several infrared heaters. In a warm environment, an infrared sauna could be open air and still heat the users in the same manner, since the heaters don't rely on the air being hot, but only hot enough such that the body doesn't cool down without sweating. All the same, normally the units are contained in a room, allowing the air to heat and in effect simulating the feel of a traditional sauna. In other words, the sauna box creates the atmosphere of the sauna while the heaters provide the actual infrared therapy.

In an infrared sauna, the infrared heater produces radiant energy, which is the same as the heat from the sun, only without the harmful ultraviolet rays. Most of these heaters draw on technology developed in 1965 by Dr. Tadashi Ishikawa, a member of the Research and Development Department of Fuji Medical.

Foot Massage:

1.Burn off the cold ,warm your body

2.Improve human body blood circulation,reduce fatigue;

3.The sleep-improvement function

4.Better for cure tinea pedis

Work environment

1. Temp:5°C~40°C
2. Humidity:≤85%
3. Atmospheric pressure:700hpa~1060hpa;
4. Power:AC 220V±22V;50Hz±5Hz

The characteristics of the machine

1.  Rectangular bucket, natural wood;

1. Micro-computer digital control system,time,temperature can be set at wil;
2. High-precision digital circuits;
3.  Special made for long service life,The best match with the human body,absorption best.

Performance index

1.              Temperature Contro:"1~5”is  the temperature that set at will  from low to high,“0”means stopping;

2.              Time control:"10,20,30,40,50,60”minutes can be set at will ;time is “00”means stopping work.

Specifications

Model:MY828

Size:450×360×500(mm)

Rated power:180w

Use and operation of equipment

Use notices :

1.Check wiring , socket load and voltage,if it meets the requirements of the instrument.

2.The product can be placed Vertically or horizontally when it is used.

3.The control of the  temperature and time should be based on individual circumstances and the ambient temperature selection co -

Proper temperature and time.

4.The equipment should be shut down for 1 hour after 4 hours continuous work.

5. Be sure to turn off the equipment switch, unplug the power plug cable after use .

Operation methods:

1.Plug into the power socket in three holes, "green" power indicator light,at this point.

2.Press the power button touch "switch", a digital tube light (red), equipment can enter the setting interfa

3.Temperature Setting: Press the "Settings" button, adjust to the desired temperature, "1 ~ 5" can be set the temperature from low to high, the temperature is set to "0", the red light eliminate, means stoppping working;

 4.Time Settings: Pressing the "temperature / time" button, two digital tube light (red), and then "Set" button adjust to the time required, time "10,20,30,40,50,60" minutes can be set at will  ;

Temperature / time have been set set, the "red" light displays light, equipment  begin to  work;

Time for "00", the "red" light displays eliminate, instruments stop working.

Safety Precautions

1.None water, if used in wet ground and should ensure that the product does not damp.

2.Don’t stack in the vicinity of inflammable and explosive materials.

3.Towels are prohibited into the bucket.

4.Don’t stand at the barrel.

 6.Any of the following persons, to prohibit  use of this instrument:

(1)Serious bleeding and festering wound .

(2)Severe hypertension.

(3)Severely burned patients .

(4)Pregnant women, babies with caution, should be with some care, children should be  under the guidance of adult when use it ;

(5)Patients with serious illnesses, frail persons, high-risk patients, heart failure persons;

(6)In vivo with those of medical electronic equipment;

(7)And temperature-related contraindications, please use under the guidance of a doctor;

7. If any queries, please use under the guidance of your doctor.

Common Troubleshooting

Instrument Maintenance

1.If it  needs to clean the surface of the instrument, you can simply use a soft, dry cloth, if still can not wipe clean,  can wipe with  neutral detergent. Wipe the box with wet cotton material after wring gently , Are not allowed to be wiped with  alcohol, gasoline and other organic solvent .

2. Prohibited wipe foot barrel  with damp cloth , so as to avoid risk of electric shock

Transport and storage of the equipment

1.Transport

Product should avoid splashing , strong rain and snow poured collisions .And do not mix with the corrosive medium transport.

 2.Storage

Should be stored in non-corrosive material, well-ventilated, dry coffers.

Service after sale

1.Users should fill the  warranty card ,and send the warranty card to our company whin one month after bought the product.

 2.Warranty period is 12 months since you bought it .

 It can be warranty With "User Profile" and "product warranty card".

3.If it is the following case will charge fees:

(1)Out of  the warranty period.

(2)Don’t show the warranty cards in warranty period.

(3)Doesn’t return the"User files" to company or the content has been altered.

(4)The reasons for non-normal use Caused failure.

(5)Damage due to transportation and the irresistible forces .

(6)Due to incorrect installation or not in accordance with instructions or in the non-working environment.

(7)The failure and damage that caused by wrong maintenances which were not approved by the company .