cctr630 kids gps watch tracker, old man watch gps tracker with free app web tracking system

Before Using:

1. Power On/Off

Power On: If the GPS watch is powered OFF, press and hold the Button ON/OFF over 5 seconds and then the LCD will display “WELCOME”, then release the button ,and the GPS watch is powered ON.

Power Off: If the GPS watch is powered ON, press and hold the ON/OFF button over 5 seconds and then the LCD will display “BYE BYE”, then release the button ,and the GPS watch is powered OFF.

    2. SIM Card Installation(Micro card): This GPS watch need a micro SIM card (every month need about 10M GPRS data according the different working mode, order an data package can save money), Open the back battery cover with finger like the following diagram, pull the battery out, and the SIM card socket can be seen, pull the SIM card metal cover to “OPEN” direction, and the cover can be opened up, and put the SIM card in the holder (Metal pin face to down), close the metal cover and push the metal cover to “LOCK” direction, after a sound of lock the SIM card has been locked and installed.

 3. Using

This GPS tracker is no installation, wear on the arm or put in the bag and power on is OK, for better hidden, drop in the bag will be better.

4. Recharging

This GPS watch uses the 5V DC voltage to recharge, connect the watch charging micro USB socket to the AC charger or PC USB, the GPS watch will begin to recharge, about 1-2 hours, the battery will be full, press once any button of the GPS watch tracker, the LCD will display the battery level.

5. Low Battery Alarm

    When the tracker battery voltage is low than 10%, the watch will send battery low information SMS to the authorized phone number. maybe a few hours later, the watch will turn off after the battery is gone out.

6. Reset to Factory Configure

Send the SMS command to the tracker can reset to the factory configuration. The SMS command is factory#. the tracker will delete all user setting and back to factory configuration and repower on.

    Notes: After back to default set, all IP / APN / GPRS / Language / Timezone / Alarm Setting etc are deleted and back to factory setting, just like a new product, all authorized phone number are deleted and password change to 123456, all the alarm setting is canceled, if the IP/APN/GPRS name & password/TIMEZONE are changed, and you need set these again by sending SMS.

7,GPS & GSM Antenna

The Antenna of GSM and GPS are built in the GPS watch.if can not locate please change a place to try again.

8. Using Condition

The working temperature is -20℃ to 60℃, over this range the specification maybe can not reach the standard level. the storage temperature can reach to -40℃ to 80℃.

Simply Using Step

1. First to buy a 2G GSM phone SIM card and enable GPRS service, order a data package (Normally will use about 10M GPRS data every month), install in the tracker, please refer the above Before Using 2.

2. Press any ON/OFF button till the watch power on, first time using please put the tracker outdoor for easy get GPS & GSM signal.

3. Please add authorized phone number first, send SMS to tracker to set your mobile phone number as center or slave center number (pw,123456,center,yourphonenumber#) , then you can use your mobile phone to send SMS to change the setting of the tracker or control the tracker. please refer the followingLocate Operation & Setting 1. (Only the center or slave center number can send SMS or call the tracker to change the setting of the tracker or control the tracker)

4. Send SMS “123#” or “url#” to the tracker with authorized phone, a few minutes later, the watch will reply the tracker location with location description or Google map link by SMS. Please refer the following Locate Operation & Setting 3 & 4.

5. Send SMS “lang,0,zone,-5#” to tracker with authorized phone to set your local time, Please refer the following Locate Operation & Setting 2.

6. Send SMS “m,4#” to tracker with authorized phone to set change the working mode, Please refer the followingLocate Operation & Setting 11.