LM-EP22 hdmi video broadcast repeater with TCP ip 120m over single UTP cat5e cable ethernet extender

Specificaton

hd ethernet extender

1. DIP Switch 
2. 802.3af POE 
3. 120m over single cat5e/cat6 cable 
4. IR, IGMP   

   LM-EP22 hdmi video broadcast repeater with TCP ip 120m over single UTP cat5e cable ethernet extender

Model NO.:LM-EP22

Key words: ethernet extender

    LM-EP22 ethernet extender  extend HDMI Signal 1080p up to 120m over single cat5e/6 cable, supports cascade and many to many network configuration. This IP HDTV Video Sender Transmitter and Receiver is a HDMI Over IP extender, flexible and scalable HDMI 1080p high quality video broadcasting with gigabit ethernet LAN, compliant HDCP, with DIP Switch and IR remote control.

Main feature

1).Compatible HDCP.
2).Flexible and scalable HDMI 1080p High Quality Video Broadcasting with Gigabit Ethernet LAN
3).Multicasting and broadcasting architecture, adding more displays without adding LAN bandwidth loading. 
4).Support Point-to-Point, Point-to-Many and Many-to-Many network configuration. 
5).Extends 1080p HDMI signals up to 120m over a single Cat5e/6 cable 
6).Built-in DIP switch to change Group ID and Utility for remotely.
7).With IR remote control of sources devices.
8).Dual power input: 802.3af compliant POE & DC5V

9).Support IGMP v.1 & v.2 address

10).Support cascading Ethernet Switches up to 3 layers

11).Up to 16 transmitters and more than 200 receivers possible in a single system

12). With POE function, no need power adapter for TX & RX when connecting with POE Switch.

Parameters

Note: 

1. Specifications are subject to change without notice. Mass and dimensions are approximate.

2. IP and MAC address must be different for one TX to many RX or many TX to many RX configuration.

Panel description

4 bits DIP Switch:

Use 4bits DIP switch to select 16 groups ID ( such as 0001,0010,0101 etc,)

Default TX unicast IP address is 192.168.168.55 , it can be configured from webpage.

TX Group IP address: 239.168.168.xx, (xx is the value of bits[2:0])

4 bits DIP Switch:

Use 4 bits DIP Switch to select 16 groups ID ( such as 0001, 0010, 0101 etc. )

Default RX unicast IP address is 192.168.168.56, it can be configured from webpage.

RX Group IP address: 239.168.168.xxx ( xxx is the value of bits [2:0])

User should configure the DIP switch within 10 seconds, firmware should reset the system 20 second after detecting the first change of DIP switch, and latch the new DIP switch value after reset.

Connection and operation

Point to point configuration: 

1. Connect one HDMI Cable between the HDMI output port of source device and the HDMI input port of Transmitter unit 

2. Connect one HDMI Cable between the HDMI input port of display and the HDMI output port of Receiver unit.

3. Connect one UTP Cat5e or better cables between the RJ45 port of Transmitter unit and RJ45 port of Receiver unit.

4. Connect 5V DC power supplies to both Transmitter unit and Receiver unit.

5. Power on the output device first and the source second. 

Point to multicast network configuration:

1. Connect one HDMI Cable between the HDMI output port of source device and the HDMI input port of Transmitter unit 

2 . Connect one CAT5e or better cable between the RJ45 port of transmitter and input port of Gigabit Ethernet switch hub.

3. Connect one CAT5e or better cable between the output port of each Gigabit Ethernet switch hub and RJ45 port of Receiver unit.

4. Power on the output device first and then the source device.

5. If DIP switch at the transmitter is set up: Group ID:0001, then DIP switch at each receiver should be  set up as same as the transmitter: Group ID:0001

Multipoint to multipoint network configuration:  

1. Connect one HDMI Cable between the HDMI output port of source device and the HDMI input port of Transmitter unit.

2. Connect one HDMI Cable between the HDMI input port of display and the HDMI output port of Receiver unit. 

3. Connect one CAT5e or better cable between the RJ45 of each Transmitter unit and RJ45 port of Gigabit Ethernet switch hub.

4. Connect one CAT5e or better cable between each RJ45 port of Gigabit Ethernet switch hub to RJ45 port of Receiver unit. User can select source channel by setting up dip switch on each transmitter unit. And select display devices for Receiver units via one remote control.

5. Use DIP switch to select sources