HX 710P Non-curable rubber modified asphalt coating for waterproofing

Product Description

HX-710P Non-curable rubber modified asphalt coating for waterproofing is a sticky and pasty waterproofing coating in application condition, and it’s made up of rubber, bitumen and auxiliaries mixed. It can be heated to flowing type, then brushed on the substrate, forming the strong adhesion, creep and self-healing function waterproofing layer. It will not only as a separate waterproofing layer, also can be applicated with waterproofing membrane to a composite waterproofing layer.

After long-term exposure to air, non-cured rubberized asphalt waterproof coating don’t curing, insoluble in water, have high bond strength, able to adapt to the complex construction operation; it can automatically search for leaks parts repair damaged the waterproof layer, to keep permanent leak proof; doesn’t contain solvents, meet the requirements of national security, environmental protection.

It has outstanding creep properties, good waterproof performance, ageing resistance, can use daub, spraying and plasma, and other methods. It can use with coil to form composite waterproof layer; and can also be alone as a waterproof layer, surface should be attached to the isolation layer.

PRODUCT FEATURES

It has superior erosion and aging resistances when applied to underground or unexposed projects.

Good high and low temperature resistance and excellent elongation

No cure: it always keeps original elastic-plastic status in lifetime with 99% solids content without solvents and volatile matters.

Superior adaptation to substrates: it is accommodative to wet or dry substrates with cracks or deformation. It permeates into void of substrates while bonded to substrates

High adhesion: long term, seamless adhesion with substrate to form integration. It is applied to wet substrate or leaking stoppages and is bonded to various articles.

High self-cure: It will be self-cured while damaged during application or in usage period to prevent water channeling between waterproofing layer and substrates to keep the continuous waterproofing layer. The coating won’t be separated to form seamless and stable waterproofing layer.

Convenient application with high efficiency: No particular skill requirement to installers. There are more application options including electrical sprayer or human spray in high efficiency and saving construction period.

Combination with other waterproofing material: Forming composite waterproofing layer and improving waterproofing performance.

Superior hydrophobicity: The definition of hydrophobicity means material wouldn’t be wetted by water when contacting with it. The non-curable rubber modified bituminous waterproofing coating will keep superior waterproofing performance in long term water soaking.

Application:

Industrial and civil building roof and side wall waterproof engineering

Planting roof waterproof engineering

Underground structures, subway station, tunnel waterproof engineering

Road bridges, railways and other waterproof engineering

Dams, water conservancy facilities and other waterproof engineering

Deformation cracks, settlement joint and other crack grouting filling and sewing

Construction points:

1. Clean up the grass-roots

When the surface of the grass-roots level obviously uneven is suitable to use cement mortar screeding, through the pipeline of the waterproof layer, embedded parts and equipment foundation shall be buried before the waterproof layer construction and installation. The gaps between the pipeline and structure should plugging tightly of fine stone concrete or polymer waterproof mortar. Use a broom or hair drier to clean up grass-roots mortar and construction waste. Acceptance of the basic level should smooth, solid, drainage slope comply with the design requirements, grass-roots level can be wet but cannot have water on the surface.

2. Detail parts additional layer construction

The place such as roof rainwater mouth, the roof tube root, the inside and exposed corner of parapet and gutter firstly blade coating 1mm non-cured rubberized asphalt waterproof coating to make strengthen.

3. Coating construction

Coating can choose blade coating or spray coating construction, open extrusion pump, to squeeze non-cured rubberized asphalt waterproof coating to the grass-roots, blade coating evenly  and full coating not exposed base,  coating thickness according to the design requirements.

4. Pave coil

Then paving the coiled material to waterproof coating surface that has completed the construction, it should laid straight, smooth, no wrinkle. Coiled material lap width is 100 mm, overlapping parts adopt cold stick form, then blade coating or spray coating non-cured rubberized asphalt waterproof coating on the coil lap width range, no need table dry time, can be directly construction overlapping parts of the coil, and rolling.

5. Water-storing test

After the completion of the waterproof layer, water storage experiment was carried out in accordance with the regulations.

Storage 24 hours no leakage water is qualified.

6. The construction of protective layer

The quality of roof waterproof layer can be qualified acceptance, protective layer construction can be going. According to design requirements do the corresponding concrete, block material or cement mortar layer.

Delivery size in 25KG bucket or customized.

Our Service

Pre-sale: We will communicate with the customers carefully to get their instruction about the order.

Order placed: We will produce the bulk order in shortest time and will communicate with you if any problem during the process and shipping the order on time.

After sale: If you have any problem after you receive the goods, we will try our best to help you solve the problem and make you satisfied.