Auto Shot Blasting Machine

SHOT BLASTING MACHINE Appliation :

1.Agriculture industry
Shot blasting:tractor components,water pumps,farm implements,etc. 

2.Automobile industry
Shot blasting:engine blocks,cylinder heads,break drums,etc.

3.Building & infrastructure industry
Shot blasting:structural steel,bars,transmission & television towers,etc.

4.Transportation industry
Shot blasting:engine blocks,axle & crank shafts,diesel engine components,etc.

5.Oil & gas industry
Surface preparation:pipes coating with paper,cement,epoxy,polythene,coal tar,etc.

6.Mining industry
Shot blasting:bulldozer,dumpers,crushers,land fill equipments,etc.

7.Foundry industry
Shot blasting:automobile,tractor,scooter & motor cycle components,etc.

8.Aluminum casting industry
Shot peening:automobile,scooter & motor cycle components,etc.

9.Forging industry
Shot blasting:crank shafts,connecting rods,torsion bars,other forged components,etc.

10.Railway industry
Shot blasting:side frames,bolster,couplers,rail wheel,entire coach,etc.

11.Electrical industry
Shot blasting:motor body,transformer tank,transmission tower,etc.

12.Energy & power industry
Shot blasting:sturbines,boilers,switch gear components,wind mill blades,column,etc.

13.Stainless steel industry
Shot blasting:strips,angles,channels,pipes,tee,etc.

14.Aviation industry
Shot peening:jet engine,blades,propeller,turbine,hubs,land gear components,etc.

15.Shipyard industry
Shot blasting:steel plates,angles,channels,beams,etc.

16.Steel mill industry

Shot blasting:strips,angles,channels,pipes,tee,etc.

17.Air polution control equipments
Applications:foundry,carbon black,furnace,cupola,etc.

18.Ceramic/paver industry
Applications:antiskid,footpath,hospital,government buildig,public places,etc.

The Introduction of Steel Plate Pre-treatment Line

The steel plate is conveyed to the rain and dirt blowing and scratching device to remove the dirt and water on the surface ,after that ,send into the pre-heating system to remove the water and
oil on the surface ,Then conveyed to the sealed shot blasting room by the rollers. The steel balls (casting steel ball or cut steel wire) are shot against the surface of steel plate after acceleration of high-speed vane wheels in the shooters in order to get rid of the rust, taint and oxide skin off the surface of the work piece by percussion and scratching. The steel ball and dust accumulated on the surface of the steel plate is cleaned away by high-strength nylon brush, steel ball recollecting spiral and high-pressure air pipe. The shot-blasted steel plate is further conveyed to the painting
room, the primary paint is applied to the surface of the work piece by the painting guns mounted on the upper and lower painting trolley, then the work piece is fed into the drying room. Then
quickly send out the work piece when its paint film reaches finger-felt dry level.

Technological Process of Steel Plate Pre-treatment Line

The adhesive force of the paint film is improved due to certain roughness produced after shot blasting; thus improve the anti-rust-ability and surface quality of the steel plate.

Main Technical Parameters

Unique Features of Steel Plate Pre-treatment Line

This is a newly-developed electro-mechanical integrated product evolved from similar production lines. The whole production line is controlled by industrial PLC imported from Japan. Touch screen
is employed for simulated indication, fault diagnosis and automatic alarming. There are 6 sets of monitoring displays in control system .

The whole-process automation is realized for the following steps:
work piece loading →in-put →pre-heating → shot blasting→ painting→ drying →output
(switch between automatic mode and manual mode is possible), which makes it convenient to manipulate the whole production line. It is quite an idealistic automatic production line for pre-treatment such as rust-cleaning, slag-removing & stress-relieving, panting etc.
Its overallperformance reaches the international advanced level among similar products.

We are factory for manufacturing alll kinds of foundry machinery and almost spare parts, We have special spare part depart.

 We offer a full maintenance service! Manufacturers can provide repair facilities for consumers and to stock adequate spare parts so repairs can be undertaken. Tel (400-1177-399)

Our factory covers an area of 26000 square meters. We have about 260 employees including more than 50 middle and senior technical staff.
Professional software such as Auto CAD and Solid works have been used to provide exact drawings. SAP, Office Automation system been used to control and smooth the work flow.

We have a Quality Inspection Center with Dynamic balance detector, Static balance tester and other advanced equipments to detect finished products, which can guarantee the quality of each product. 
All the products are designed by our technical department and tested by our own quality supervise department. We have the ISO9001 International Certification and CE Certification.

Our machine had approved CE AND ISO AND BV  , SO OUR MACHINE CAN EXPORT TO ALL COUNTRIES.

1). Q: Do you have after sales support?
A: Yes, we are happy to give advice and we also have skilled technicians available across the world. We need your machines running in order to keep your business running.

2). Q: How do your machines compare with other big companies in this market?
A: We are up to date with the latest technology and improve our machines accordingly

3). Q: How does your factory do regarding quality control?
A: Quality is priority. MACTEC People always attach great importance to quality control from the very beginning to the end of the production. Every product will be fully assembled and carefully tested before it's packed for shipment.

4). Q: Do you sell only standard machines?
A: No, most of our machines are built according to customers specifications, using top brand name components

5). Q: Will you deliver the right goods as ordered? How can I trust you?
A: Yes, we will. The core of our company culture is honesty and credit. MACTEC is ALIBAB’s Gold supplier with BV assessment. If you check with ALIBABA, you will see that we have never got any complaint from our customers. 

6).Shot Blasting Machine is often used for: 

Cleaning
Deflashing
Rust and Scale Removal
Anchor Pattern Creation
Peening
Coating Removal

Small-sized machine will be pakced by wooden box 

Medium-sized machine will be no bulk and load into container directly

Large-sized machine will be load into  special container ( skeletal container or  open top, flat and platform containers)

Welcome to contact us or visit our company.

There are some shot blasting machines for cleaning pipe , tube, casting parts and soon on. 

There are blast chamber at our factory