Available For Electrical Industry Wide-strip Shot Blasting Machine

Blasting principle
Shot blasting process uses a transverse principle applies to straight wide strip, throwing the first use of variable frequency motor drive, stepless adjustment of speed pellets projectile speed by throwing the first.
Shot mode you can adjust the orientation applies to two different sets of strip width. Therefore, the best pellets intensity distribution and use of blasting stream can be guaranteed.

Pellets circulatory system
In the blasting chamber by shot blasting pellets into steel projectile motion, a mixture of pellets and scale at the bottom of the blasting chamber collected and transported through the screw conveyor bucket elevator. Minimum diameter pellets bucket elevator vertical transport of the pellets mixture up to the upper screw conveyor, screw conveyor and transported to the pellets separator in the separator, pellets from impurities and small pieces of material (less than requested ) separated and fed into a hopper, feed pellets quantity supplied to the valve for adjusting the throwing head.

3XQ6914X series wide-strip blasting descaling machine
Mainly is：Access platform (upper platform, the lower platform 1 set) 1 set, shot blasting chamber (including lining shield) 3 sets, blow pill chamber 3 sets (including intermediate purge chamber liner sheeting, eventually purged each room sets a), shot blasting assembly 12 sets (including motor and transmission), the bottom of the screw conveyor 3 sets of roller conveyor 1 set, projectile control system 1 set (containing 12 pellets inlet valve and remote control system), bucket elevator 3 sets, pill residue separator 3 sets (including the upper part of the screw conveyor, pellets separators, storage hopper, screw conveyor and other waste), projectile compensation system 1 set, 3 sets of ventilation and dust removal system ( including inertial dust collector, bag filter, fans, motors, pipes, butterfly valves, chimneys, etc.), and the fan blowing pill pipeline (including 3 sets 3HE-200 blower and pipes), pneumatic control system, electrical control system.

3XQ6916X The shot blasting machine, together with auxiliary equipment is stainless steel with a straight-through manner annealing, cooling, after breaking scale, the mechanical descaling and pickling device design. The shot blasting machine is designed in accordance with the requirements of product mix. In actual speed through strip steel, oxide type, strip width, annealing capacity may be. According to ISO8501-1: 1988 standard, the quality of the strip surface reaches Sa2.5 after blasting.

Blast wheel：
Length about（Free ladders length）14400mm
Length about（With enclosures）19000mm
Width about（With enclosures）8200mm
Height about 8500mm
(Determined in accordance with the actual bus design height) on the ground by the strip line height
Enclosures exterior noise (strip exit / entry except) ≤85Db (A)
Blast:
Quantity（12set）
Type（With pneumatic adjustment means sets the orientation）QSX105*500
Blade quantity（8pieces）
Width/diameter 105/500mm
Speed（frequency）1500-250rpm
Shot speed about 52-78m/sec
Max blasting capacity 1100kg/min
Power 12*90Kw

Roots Blower:
Use fans to provide compressed air on the pellets will blow away the surface of the strip, the following data are fan parameters：
Wind spproc.3600m³/h
Stress 0.68bar
Power 110Kw
Dust collector:
Effciency 99.99%(For dust particles of 1 micron)
Gas-to -cloth ratio <1.5m/min
Wind：50000m³/h
Filter: polyester needle felt
Tempature ≤150℃
Power 75Kw
Clean air dust content：<50mg/Nm³
Total power:1700kw
Power supply 3*380V±10% 50Hz±0.5Hz
Control voltage24DCV±10%

1. Reply your inquiry in 24 working hours.
2. Experienced staffs answer all your questions in fluent English.
3. Customized design is available. UEM&UBM are welcomed.
4. Exclusive and unique solution can be provided to our customer by our well-trained and professional engineers and staff.
5. Special discount and protection of sales are provided to our distributor.
6. Professional factory :We are manufacturer, specializing in producing all kinds of machinery for more than 20 years, competitive with good quantity.
7. Sample: We can send out sample for test in one week if the order quantity is big enough. But the shipment charges is usually paid by your side, the charges will be rebounded when we have formal order.
8. As an honest seller, we always use superior raw material, advanced machines, skilled technicians to ensure our products to be finished in high quality and stable feature. Welcome to contact us or visit our company.