Sino-Telecom One Line ADSL Line Extender VOIP Amplifier AER800-1P

General Description

ADSL loop extender can extend the coverage of ADSL lines. It will provide systems with higher performance-to-cost ratio, improve the equipment utilization rate and optimize the network. This product will allow you to double the number of subscribers that you can reach while offering more consistent high bandwidth services to your existing customers.

ADSL loop extender is an active element installed in the outside loop plant. It operates as an amplifier and equalizes the signal.

ADSL loop extender’ box and the business card are as below:

• AER800-1P box: One box for 1 AER800-1P embedded.
• AER800-4P box: One box for 4 AER800-C1P and 1 AER800-PWR embedded.
• AER800-8P box: One box for 8 AER800-C1P and 1 AER800-PWR embedded.
• AER800-C1P: One port ADSL loop extender for one ADSL subscriber, can be inserted into the extender’s box easily.
• AER800-PWR: One port power supply, which can power for 1~8 AER800-C1P cards, can be inserted into the extender’s box easily.

Benefits

• ADSL subscriber can be added by inserting the business cards AER800-C1P.
• Economize the copper pairs for one additional pair can power eight ADSL subscriber.
• Comprehensive over-voltage protection.
• Easy to install, deploy and maintain.
• Low power consumption and more environmentally friendly

Technical Specifications

Technical specifications

Technical specifications of AEC-B1P/B4P/RACK

Application

1. Equipment connection diagram:

ADSL Loop Extender Application Diagram

L1: The signal-twist pair connecting ADSL Loop Extender to DSLAM.

L2: The signal-twist pair connecting ADSL Loop Extender to Modem.

L3: The power twist pair connecting AEC to ADSL loop extender.

2. Resistance and distance demand

The recommended installation conditions are as follows:

(1)24 AWG(0.5mm) twist pair

The Demand about Resistance and Distance of 24AWG:

(2)26 AWG(0.4mm) twist pair

The Demand about Resistance and Distance of 26AWG:

Physical Structure

AER800-xP ADSL Extender Series

1. AER800-1P Box

AER800-1P Box

Twist-pair Connection Description of AER800-1P

2.  AER800-4P Box

AER800-4P Box

3.  AER800-8P Box

AER800-8P Box

AEC Remoted Power Supply Series

1. AEC-B1P (1 port output)

AEC-B1P

Attention:Two-core power cord without plug: used for DC48V power input, no polarity.

Three-core power cord with plug: used for AC 110V/220V power input.

AEC-B1P connector wiring diagram

2. AEC-B4P (4 port output)

The description of terminal

Installation Procedure

1. Unpack

When unpacking the equipment, be sure to check the contents of the packaging for completeness against your purchase order. Notify your supplier immediately if any items are missing.

Note: Please save packing material. All equipment returned must be packed in the original packing material.

Be sure to inspect the equipment for shipping damage, including bent or loose hardware, and broken connectors. If the equipment appears to have been damaged in transit, please contact your supplier.

2. Install the remote power supply

(1) Generally, the Power Supply is installed at CO side. The type of power supply ordered should be right, either AC110V /AC220V or DC48V.

The Power supply also can be installed in the CPE or near the extender.

(2) One Spare copper pair is needed for deliver power to AER800-1P/2P/4P/8P.

(3) Before installation, the DC 48V or AC110V~AC220V power supply should be grounded reliably.

(4) DC 48V Power input is non-polarity.

(5) The output of DC116V is non-polarity.

Attention:

1. Ground terminal should be grounded reliably. Copper-core wire with no less than 2.5mm2 section area is required as ground wire.

2. Remote power supply should not be turned on until the extender installation is finished.

3. When the power supply wire is active, do not touch both two wires of the twist pair simultaneously.

3. Install the ADSL loop extender

(1) Fix the AER800-1P/2P/4P/8P box in the junction cabinet or at the supplied mounted brackets. Ground the box through the grounding screw in the bottom outside the box.

Attention: Copper-core wire with no less than 2.5mm2 section area is required as ground wire. One end of the wire should connect to loop extender’s ground terminal. The other end of the wire should connect to a good ground point.

(2) Connect the cable

AER800-1P/2P: Connect the power line with blue/white pair wire,CO signal line with orange/white, CPE signal line with green/white pair wire.

AER800-4P/8P:Connect the power input line into the AER800-PWR. Connect the signal line to AER800-C1P, the line from DSLAM to the “CO” socket, the line to the modem to the “CPE” socket.

Attention: The power supply should not be turn on until the extender installation is finished.

(3) Power on

Power on after confirming that all the twist-pair cables are connected correctly and box is securely installed.

For AER800-4P/8P, when AER800-C1P card is used, please make sure “power switch bit” is set to “ON”, when AER800-C1P card is not used, please make sure “power switch bit” is set to “OFF”.

Product Category

1. WDM Optical Transport System                               2. Optical Line Protection Switch

3. xDSL                                                                           4. GPON/EPON

5. Lawful Interception                                                   6. Network Interface Card

7. TAP                                                                             8. Wireless AP

FAQ

1. What are your terms of payment?

Usually, we can accept T/T, PayPal and Western Union. You can select the terms of payment which is more convenient for you.

2. What about the lead time?

Usually, if there is stock of goods, we will deliver the goods within 3~5 work days after we receive the payment.

3. How about the shipping?

Usually, we will deliver the goods via International Express like FedEx, DHL, TNT, and UPS and so on. Door to door delivery service will be provided.

4. How can I place an order?

(1) Agreement is achieved on the product price and product specifications.

(2) We make proforma invoice for your confirmation.

(3) When you agree on the proforma invoice, you make the payment.

(4) We deliver the goods after we receive your payment.

5. Can you do OEM for us?

Yes. If there is a certain order quantity, we can do OEM including printing, logo, and customized model for you.

6. What are the advantages of your products?

A. Good quality and competitive prices.

B. Strict quality control during production process.

C. Professional operations in processes of production, sales, assembling, packaging and shipping.

D. Good after-sale service. Professional online technical support can be provided. Moreover, if there is any problem of the goods, we will help to solve the problem or provide replacement of the goods.