Automatic MVR Industrial Evaporator Concentrator Distiller

                                      MVR  EVAPORATOR

Application:

Mechanical vapor recompression (MVR) evaporator is used for milk, glucose, organic acid, VC, xylose, pharmaceutical, chemical, biological engineering, environmental industry, waste recycling industry, paper making industry, salt making industry and so on.

Structure Drawing:

Structure:

MVR evaporator includes pre-heater, heater, pump, separator, vacuum system, compressor system, automatic control system, cleaning system and so on.

Principle:

To feed the material from raw material storage tank through feed pump, the preheating system and the heating system into the heater and the separator. To stop feeding when the liquid level reaches the setting height.

Then to start material circulating pump, the liquid will be circulating in the heater and the separator, to open the steam valve to heat the raw material, when the temperature is reaching the setting temperature, then turn on the vacuum system and compressor, the impeller speed  is gradually increasing, then the system is evaporating, at the same time, the raw material is continuously entering from the bottom of the heater, it is like film flow from bottom to up, it is also heated by steam until boiling, the steam is spraying out from the arc guide groove to separator, the steam will be rotating rise along the wall of the separator and exhaust into compressor, the liquid will drop down to bottom of the separator. The temperature of pure steam will rise after compression, this recycled steam can heat the heater again, so it can save energy. The recycled steam will be cooled and became into hot water which flow into pre heater, to heat the raw material which flow into heater and separator, so the whole system maintained at a constant feed, discharge, evaporation.

Character:

MVR evaporator is new technology for modern industry

1. MVR Evaporator saving technology is the most advanced of the current international evaporator technology requires only a very small amount of Health and steam (when start up, need a small amount of steam, normal operation, is almost no need for the steam), greatly reduce business operating costs, reduce environmental pollution.

2. As a result of compressors to provide heat, and compared to conventional evaporator, the temperature difference is much smaller, to achieve a moderate evaporation, which greatly improve product quality and reduce fouling.

3. No condenser or only a small area condenser, structure and process is very simple, fully automatic, continuous operation, safe and reliable.

4. Equipment with CIP cleaning within the pipeline can be realized inside cleaning, the entire device easy to operate, no dead ends.

5. The evaporator is a material at low temperatures ( evaporation temperature 45℃-75℃ )and does not generate foam under the state of evaporation, liquid evenly, do not run material, not easy to coking, minimum denaturation for heatinf material.

1.What is your raw material?

2.How much is original degree of raw material?

3.How much the finished degree of product do you want to get?

4.How much liter do you want to evaporate per hour?

5.When do you need this machine?

User demands analysis

Engineering design

Product manufacturing

Automatic control integration

Certification service

Engineers are available to go abroad to help installation

All the products before delivery should be tested by assemble & debugging engineer, wiped up and cleaned, then wrapped by stretch film to protect it from moist. The precision part need to flexible package. In addition, without standard tools, manual and other documents, and allow ex-factory confirmation sheet, the machine cannot leave factory.

All the products will be packed in wooden case. The exported products use plywood case to pack.

The foot margin of equipment fixed tightly to make the machine can experience loading & uploading, the upward mark will be posted on the wooden case. 

Our company is professional to manufacture and export pharmaceutical machine, food machine. Machines include:

Pharmaceutical machine:

Tablet press machine, blister packing machine, capsule filling machine, capsule / tablet counting production line, soft capsule making machine, mixing machine.

Liquid filling machine:

Vial filling machine, ampoule filing machine, wrapping machine, tube filling and sealing machine.

Food machine:

Jam, butter, chocolate packing machine, food tablet press machine and so on.

Export:

Machines have exported to South America, Europe, South-east Asia, and so on.

Welcome to contact with us.