Remote collar pet training with Digital Voice

Specifications

remote pet training collar with digital voice

controller functions

1.match button(y)- use for match the receiver with controller,one controller with three receiver collar is available for this unit.

2.mode button- change mode,together four modes-vibration  -  static impulse -  vibration&static  -  play voice.

* press mode button, no.1 vibration indicator light will light, means only vibration.

* press mode button again, no.2 static indicator light will light, means only static impulse.

* press mode button the third time, no.1 vibration & no.2 static indicator light will light together, means vibration and static impulse work at the same time.

* press mode button the third time, no.3 play voice indicator light will light together, means play the voice.

cycle as above.

3.transmit button(ok)- transmit signal. transmit the signal that had set already to control the receiver collar.

4.on/off switch konb - turn on or turn off this unit and can adjust the level of vibration and static.

5.play button- use for play the record message.

receiver functions

1. contact point- static correction will deliver from the contact point and effectively curb the improper deeds of the pet.

2. charge electrodes- multi-functions(such as charge function, power on/off, record ) . details as below-

* charge function- connect with the recharge equipment charge the built-in battery of the receiver.

* power on/off function- short-circuit the charge electrodes.the receiver will issued di... a long ring ,which means the receiver is power on. short-circuit the charge electrodes of the receiver for more than 2 seconds, the receiver will issued di… di… two long rings,which means receiver is power off.

match time is in 3 seconds after you power on the receiver.two beeps from receiver means the receiver is matched, one short beep after 3 seonds means you are failed.

* record function- the receiver collar has record function, can record 5 seconds message.

at the power on status,short-circuit the charge electrodes,one beep will from receiver, then you can start to record your message, after 5 seconds will have one beep from receiver means finish the record.

operation instructions

section one

match

one controller can remote three receivers at the same time.

1. match with the no.1 receiver

(1). set the transmitter- first you should install three aaa battries and turn on the switch knob,the red light of the double color light and no.1 indicator light will light together which means it can begin to match with the no.1 receiver.

(2). set the no.1 receiver- short-circuit the charge electrodes,you will hear one long di... which means the receiver has already power on and go in match time(3 seconds).

(3). operation of match- after power on, press the transmit button(ok) in 3 seconds, you can hear two di...di… sound from the receiver. it shows matched successfully. on the other hand,if you just hear one di… it shows matching failed.you should do the short-circuit again for 2 seconds,you will hear two long sound di…di… which imply the receiver has already turned off. at this time, just repeat the step (2) and the step (3) until matching successfully.

2. match with the no.2 receiver

(1). press the match button(y) again, the green light of the double color light and no.2 indicator light will light together which means it can begin to match with the no.2 receiver.

(2). match the no.2 receiver, same as the above step (2) and step (3).

3. match with the no.3 receiver

(1). press the match button(y) the third time, the green and red light of the double color light and no.3 indicator light will light together which means it can begin to match with the no.3 receiver.

(2). match the no.3 receiver, same as the above step (2) and step (3).

attention-please adjust the double color light into red when remote control the first receiver, adjust the double color light into green when remote control the second receiver ,adjust the double color light into red and green when remote control the third receiver .that is to say the light of double color indicator light of the transimitter when at remote time shall be exactly with the light when matching .otherwise you can not remote the receiver.           all the tests below are at the same way.

section two

record

the receiver has record function- at the power on status, short-circuit the charge electrodes of the receiver(short-circuit time could not more than 2 seconds), you will hear one di… from the receiver means enter into record mode, at this time you can record the message. after 5 seconds a beep di… means record finished.

attention- just short-circuit the charge electrodes once,do not continue shot-circuit it. otherwise you can’t finish the record.  if you had short-circuit it many times as some reasons, you need to stop operation, and after 5 seconds, short-circuit the charge electrodes again to enter into record mode.

section three

play test

after the above tests, you can do play test, check if your sound is recorded or not.

press match button(y) to adjust the color of the double indicator light same as when matchs. which means if the light color(double color indicator light) of the transmitter is red when you match with the receiver,you also need to adjust it to red light at the testing. if the color of the transmitter is green when you match with the receiver,you also need to adjust it to green light at the testing.

press mode button to make the no.3 indicator light light, then press the play button, transmit indicator light will light and the receiver will play the record message which you had recorded.

section four

functions test

after the above tests,you can begin to test the function.

when you test the receiver, set the color of double color light same as when matched.

use no.1 recevier for example, at this time, the green light of double color light will light.

1.  press mode button to adjust the no. 1 indicator light light, then press the transmit button, the transmit indicator light will light, at the same time, the receiver begin to vibrate, you can use the on/off switch knob to adjust the level of the vibration.

2.  press mode button again, the no.2 indicator light will light. then press the transmit button, the transmit indicator light will light, at the same time, the receiver begins to release static, you can use the test light to test it.use the on/off switch knob to adjust the level of the static.

3.  press mode button the third time, the no.1&no.2 indicator light will light together. then press the transmit button, the transmit indicator light will light, at the same time, the receiver begins to vibration&release static together.use the power on/off switch knob to adjust the levels. (adjust the levels based on the type of your pet)