7000mah Long Battery GPS Tracker Based on GSM/GPRS Network and GPS Satellites Free Tracking Software big battery gps tracker

Brief Introduction

This product is based on GSM/GPRS network. It provides GPS/LBS dual positioning function to realize the management for students and company personnel. This product is with the latest GPS chip and GSM chip. It guarantees the accuracy and fast uploading to the system and makes it realizing the real-time locating and monitoring.

4.Notes for Use

l  For better use of this device, please read the user manual carefully before using;

l  The device is based on GSM/GPRS network; please use it within the area covered by GSM/GPRS network

l  The External Battery is lithium battery, voltage rating is 4.2V

5.   Parameters

6. Operating Instructions

6.1  LED Indication

Power on:

Red LED flashes quickly, the device powers on;

Green LED keeps on for 20s and then off, GSM register successfully

Green LED keeps on for 20s and then off, device gets the GPS signal.

Red and green LEDs are both off, device starts working normally.

Power off:

Red LED keeps flashing.

In-coming call:

Green LED keeps on for 1s.

When the power is too low, the red LED flashes twice, the screen reminds low power.

Charging:

When you charge the device, the red LED will be on;

When the device is full charged, the green LED will be on.

6.2  Cell phone SIM Card Number Binding

After the device powers on, please binding cell phone numbers first. There are three buttons----First Quick Dial, SOS and Second Quick Dial. First Quick Dial and Second Quick Dial each can bind 1 cell phone number in the meantime; SOS button can bind 3 cell phone numbers. Press the SOS button for 3s, device will send SMS to all of the binding numbers automatically with the location address and will take turns to call the binding numbers.

In addition, you can also bind a special SOS number by sending command (This number can activate the Voice Control Dial-Back function by sending GT and answer the phone call called by voice control Dial-Back.).

6.2.1  Quick Dial Number Binding

Send SMS command: QQ11,cell phone number    

                     QQ21,cell phone number

Command format: QQ11,13800138000

Reply format: QQ11,OK

PS: QQ11    Binding the number of the First Quick Dial

      QQ21    Binding the number of the Second Quick Dial

6.2.2  SOS button Number Binding

 Send SMS command:SOS1,cell phone number    

                      SOS2,cell phone number

                      SOS3,cell phone number

 Command format:SOS1,13800138000

 Reply format:SOS1,OK

Note: If you want to replace the number you bound, you just need bind a new one to replace it.

6.2.3  Special SOS Number Binding

 Send SMS command:SOS,cell phone number

Command format:SOS,13800138000

 Reply format:SOS,OK

If you want to replace the number you bound, you just need bind a new one to replace it.

6.3  Quick Dial Number Binding Cancellation

     Send SMS command:DELQQ,11

                         DELQQ,21

 Command format:DELLQQ, 11

       Reply format:DEL, OK

     PS: DELQQ,11  Deleting the number of the First Quick Dial

         DELQQ,21  Deleting the number of the Second Quick

Dial

6.4  Get Terminal Position by SMS

    Send SMS command: DWto the SIM Card in the device, it will reply the terminal current geography location map link.

  Command format:DW

     Reply format:

/maps/?f=q&hl=en&&q=31.237395,121.390373333333;S=0;D= 2014-10-23

6.5  Geo-fence Setting

      Please note: this function only can set successfully after the

device get the location. The device will take the current position as the center of the circle. After you use this function, when the device is out/in the range you set, the device will send SMS alarm to the special SOS number.

     Send SMS command:CWL, mode, radius range

     Command format:CWL,1,20   (Activate)

                       CWL,0       (Close)

PS: mode=1 means activating this function, mode=0 means close this function; the minimum radius range is 15m.

     Reply format:  CWL,1,OK

                    CWL,0,  OK

     PS: 20 means the radius is 20m.

6.6   Voice Monitoring

        Only the special SOS binding number can use this function.

      Send SMS command:GT,1  to the SIM Card in the device,

device will make calls to the special SOS binding number

and you can realize the remote monitoring.

  Command format:GT,1,       ON

                   GT,0       OFF

Reply format:GT, OK

6. 7   Blind Spots Uploading

         At the blind areas without GPRS signal but with GPS signal, the device can keep 2000 data point. These data points are kept according to the uploading time. If you don’t change the uploading time, the device will keep the data points every 15s.When the device get the GPRS signal, it will transfer the data to the server. If the device is turned off or the transfer is finished, the store in the device will be zero clearing.

6.8   Electric Quantity Checking

        Send SMS command:SR,1   to the SIM Card in the device, device will reply the status of the electric quantity.

      Reply format:Battery: 100%

6.9   Low Battery Alarm

       If the device is supplied power by the build-in battery only, when the electric quantity is lower than 10%, the device will send low battery alarm to the binding number and the platform.

      Alarm format: battery low!

6.10  Power Saving Mode Setting

        You can set the mode to save the battery by sending commands

      Send SMS command:MD,1      ON

                          MD,0       OFF

      Reply format:MD,1,OK

                   MD,0,OK

6.11  IP Setting

        Send SMS command:SERVER,0,IP/DNS address,Port 

       Command format:SERVER, 0, 58.64.200.21, 6780

       Reply format:SERVER, 0, OK.

6.12  GPS Uploading Time Setting

        Send SMS command:UP,time       

       Command format:UP,60  (Upload Time:60s)

       Reply format:UP,OK.

6.13  Terminal Information Checking

      Send SMS command: CX to the terminal’s SIM card, get the basic information of the terminal.  

Command format:CX

      Reply format:

IMEI:353505320000000;IP:0.0.0.0;port:0000; 

APN=cment,user==0000  

7.   Live Tracking Monitoring Platform

       Global tracking service platform website:

If you already have a login account (cluster account or IMEI

account),you can login in directly; otherwise you have to

contact your distributor to get the account and password.

  Fill in the address of the website to login in.

English Version

Cluster User Account

Demo Account: Demo

Demo Password: 123456

English Version

IMEI User

Account: Last 10 digits of IMEI number

Password: 123456

8    Tracking by Android and IOS APP, WECHAT platform

        Please enter the website of tracking service, use your phone to scan QR Code and download the APP.