Polyurethane waterproofing coating

1.The time of drying and curing is two times as fast as general single-part PU waterproofing coating, which could greatly shorten the construction stage.

2.Because of the more scientific and precise control of dynamic viscosity, little deposit is produced so that substantially reducing the waste of coating deposit.

3.Good function of physical mechanics, its tensile strength, extension rate, etc all far superior to GB standard of typeⅠandⅡ.

4.Almost no smell, especially suitable for poor ventilation environment

5.Various performance indicators are very good, but its price is moderate compared with the domestic similar products. So its performance-to-price ratio is high.

For important waterproof engineering, edible pool, aquaculture, special pool, swimming pool, water pipes, with requirements of environmental protection waterproof engineering on groundwater, etc.

1.Can be exclusive used or can be used with other waterproof coiled materials.

2.The coating is dry and not re-sticky after curing;

3.Not containing toxic and harm solvents like methylbenzene, di-methylbenzene, tri-methylbenzene, etc;

4.Not containing volatile solvent and strong smell;

5.For immediate use, it is convenient to use and can be flame plating and shelling-out;

6.Good function of physical mechanics, satisfying all indexes of typeⅠandⅡwaterproof coating.

7.The time of drying and curing is obvious shorter than national standard, which is good for construction stage;

Base Course Requirement:

The base course should be clean, solid, smooth, no dust, grease and water.

1.Coating construction is generally 3~4 times, scraping and coating on the base course evenly with a rubber scraper or bristle brush after stirring. The first time coating film should be thin in order to prevent bubbling.

2.The construction protect layer must be done upon coating thickness had met the design requirement and gained acceptance.

3.Coating can be carrying on as soon as the prior film is non-stick.

4.In order to cohering the waterproof layer and other materials, you can add some coarse sand before the last coating becoming non-sticky under facade construction.

5.The direction of the prior and the next coating should be vertical and repeated for many times to make sure that the coating is completely saturating and cohering the base course. The second time coating can be carrying on as soon as the prior film is non-stick.

6.In order to cohering the waterproof layer and other materials, you can add some coarse sand before the last coating becoming non-sticky under facade construction.

7.The construction protect layer must be done upon coating thickness had met the design requirement and gained acceptance.

*Do not construct under 5°C.

*Add a certain proportion of drier to ensure the curing time in low temperature. (Please ask technical support department for details.)

*Please wear protective clothing when you are working in order to avoid the coating contacting skin and eye. Keep ventilate.

*The coating must be tightly preserved if not running out.

*Do not construct in sleet and sand blown by the wind. Avoid constructing in high temperature at noon (prevent the coating bubbling and becoming sticky to feet).

*The products should be sealed storage in ventilated and shade place. Keep away from fire. Prevent sun and rain during transportation.

Transportation and packaging:

*It must be stored in cool, dry and ventilated space.

*Avoid raining, insolating, squeezing and colliding during transportation to save the packaging.

 .

We produce SBS/APP modified bitumen waterproofing membranes, Self adhesive bitumen waterproofing membranes, Self adhesive bitumen flashing tape, Self adhesive butyl waterproofing tape, PVC/TPO/HDPE/EVA waterproofing membranes, Polymer compound waterproofing membrane, Liquid bitumen coating, etc, our company also export Non woven polyester mat for bitumen membranes, Glassfiber mesh compound mat for bitumen membranes, Glassfiber mesh, Modified bitumen membrane production lines, etc

Our products are sold in over 20 countries all over the world. Approximately 70% of the total produced materials are supplied to the China market while the remaining 30% are exported to European countries, Middle East, South East Asia, South American and U.S.A.

Honest is our business policy, quality and service first. The key of the successful activity in the high quality of research and controls before, during and after production.