Smart temperature control heating Li-ion battery 7.4v 5200mAh

Specification 

1. Nominal voltage: 7.4V

2. Working voltage range: 6V-8.4V
3. Nominal capacity: 5200mAh
4. Charging voltage: DC 8.4V
5. Charging current: DC 1.0A
6. Standby current: ≤15μA
7. Maximum output power : 20W
8. Working efficiency: ≥99%
9. Charging method: CC/CV
10. Working temperature: -30C~+60C
11. Standard charging time: 5-6 hours
12. Charge & discharge cycles: 500-800 times
13. Protection function: over-charge , over-discharge , over-current, over-voltage , over-temperature and short-circuit protection
14. Over-charging test voltage: 8.4±25mV ; Over-charging relieve voltage: 8.05±50mV ; Over-discharging test voltage:5.5±80mV; Over-discharging relieve voltage: 6.0±100mV ; Over-current test voltage: 0.150±20mA
15. Temperature protection in samrt li-ion battery , when the batteries' temperature at 65-75C , the temperature protection circuit start , the smart li-ion battery close .

Temperature performance
1. Discharge temp. range: -20C-+60C
2. Charge temp. -20C-+40C
3. When temp. is at -20C or +60C , discharge capacity should be not less 70% than standard capacity

Vibration requirement
1. Frequency: 10-50-10HZ
2. Amplitude: 1.5mm
3. Time: 45min ( no load )

Drop test
1. Height: 1.0m
2. Floor: wooden

Operation Instruction

Connecting the battery and the plug which joint to heated piece.

The battery indicator

1)  Without load—press ON/SETUP, Power LED is red ,then the battery power is about 90%

2)  Without load—press ON/SETUP, Power LED display orange, then the battery power is about 60%

3)  Without load—press ON/SETUP, Power LED display green,then the battery power is about 25%

Five-steps intelligent power output Connecting load

1)   Press ON/SEUTP,when power LED is red ,the power output is 98%.

2)   Press ON/SEUTP button,,when LED display orange,the power output is about 75%.

3)   Press ON/SEUTP button,when,LED display green,,the power output is about 50%

4)   Press ON/SEUTP button,when,LED display lights flashing,,the power output is about 25%

5)   Press ON/SEUTP button,when LED lights turned off,no output power.The battery stops working and    shutdown.

6)   Input AC100V—240V 50-60HZ;Output DC 8.4v 1.0A

7) When the charger red LED turns into green,the battey is charging full. 

Charger
1. Input: AC 100V-240V , frequency: 50-60Hz
2. Output: DC8.4V 1.0A
3. Charging indication: when charging , the digital tube display 9 and it flickers , when charging complete , if not use it urgently , can keep charging it for longer about 0.5-1.0 hour

Safety Notice  

1. Please use the right charger to charge this battery; 

2. Please don’t dismounting the battery; 

3. If do not need to use this battery for a long time , please make the battery be fully charged and stock proper , and charge it every three month; 

4. Don’t let the battery closed to fire , don’t charge, use or stock battery in high temperature or humid condition.

 Maintenance and after-sell service

1. Charging battery to 50%-60% power if no need use , storage temperature at 20C±5C , humidity : 45%-85% and under the circumstance that the child cannot get it easily. 

2. We offer one year warranty for our products , if there is any defective within our warranty , we will send you its replacement soon free of charge . 

Product picture