Meanwell PLM-40-700 40W AC Dimmable LED Power Supply 40W led driver power supply led driver constant current

MODEL

PLM-40-700

RATED CURRENT

700A

OPERATION VOLTAGE RANGE Note.4

28 ~ 55V

CURRENT RANGE

0~ 700mA

CURRENT ACCURACY

±5.0%

RATED POWER

38.5W

RIPPLE & NOISE (max.)   Note.2

6Vp-p

NO LOAD OUTPUT VOLTAGE (max.)

60V

SETUP TIME    

500ms/115 VAC, 230VAC at full load

INPUT

VOLTAGE RANGE     Note.3

90~295VAC   127~417VDC

FREQUENCY RANGE

47~63HZ

POWER FACTOR

PF≥0.97/115VAC, PF≥0.95/230VAC, PF>0.9/277VAC (at full load) (Please refer to “Power Factor Characteristic” curve)

EFFICIENCY (Typ.)

87%

AC CURRENT (Typ.)

0.5A/115VAC   0.3A/230VAC 0.25A/277VAC

INRUSH CURRENT (Typ.)

COLD START 15A (twidth =75us measured at 50% lpeak ) at 230VAC

LEAKAGE CURRENT

<0.5mA/240VAC

PROTECTION

SHORT CIRCUIT

Hiccup mode, recovers automatically after fault condition is removed.

OVER TEMPETRATURE

100~+10°C (TSW1)

Protection type: Hiccup mode, recovers automatically after temperature goes down.

ENVIRONMENT

WORKING TEMP

-30~+60°C (Refer to “Derating Curve”)

WORKING HUMIDITY

20~90%RH non-condensing

STORAGE TEMP., HUMIDITY

-40~+80°C 10~95%RH

TEMP. COEFFICIENT

±0.03%(0~50°C)

VIBRATION

10 ~ 500Hz, 2G 10min./1cycle, period for 72min. each along X, Y, Z axes

SAFETY&EMC

SAFETY STANDARDS

UL8750, CSA C22.2 No. 250.13-12 (for PLM-40-1400 / 1750), ENEC EN61347-1, EN61347-2-13, EN62384, IP30 approved

WITHSTAND VOLTAGE

I/P-O/P:3.75KVAC

ISOLATION RESISTANCE

I/P-O/P:>100M Ohms / 500VDC / 25°C/ 70% RH

EMC EMISSION

Compliance to EN55015, EN61000-3-2 Class C(≥50% load), EN61000-3-3

EMC IMMUNITY

Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, light industry level, criteria A (surge 2KV)

QTHERS

MTBF

Khrs min. MIL-HDBK-217F(25°C)

DIMENSION

175*42*24mm(L*W*H)

PACKING

Kg;  pcs/   Kg/ CUFT

NOTE

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25°C of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Derating may be needed under low input voltage. Please check the static characteristics for more details.

4. Constant current operation region is within 50% ~100% rated output voltage. This is the suitable operation region for LED related applications, but please reconfirm special electrical requirements for some specific syestem design.

5. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.

6. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.