Meanwell waterproof electronic led driver HLG-185H-54 185W 54V led dimmable driver

MODEL

HLG-185H-54

OUTPUT

DC VOLTAGE

54V

RATED CURRENT

3.45A

RATED POWER

186.3W

RIPPLE & NOISE (max.)        Note.2

200mVp-p

VOLTAGE ADJ. RANGE          Note.5

49 ~ 58V

CURRENT ADJ. RANGE

Can be adjusted by internal potentiometer A type only

1.72 ~ 3.45A

VOLTAGE TOLERANCE        Note.3

±1.0%

LINE REGULATION

±0.5%

LOAD REGULATION

±0.5%

SETUP. RISE TIME     Note.7

2500ms, 80ms at full load     230VAC / 115VAC ; B type 2500ms, 200ms at 95% load     230VAC / 115VAC

HOLD UP TIME (Typ.)

16ms at full load     230VAC /115VAC

INPUT

VOLTAGE RANGE       Note.4

90 ~ 305VAC 127 ~ 431VDC

FREQUENCY RANGE 

47~63HZ

POWER FACTOR (Typ.)

PF>0.98/115VAC, PF>0.95/230VAC, PF>0.92/277VAC at full load (Please refer to "Power Factor Characteristic" curve)

EFFICIENCY (Typ.)

94%

AC CURRENT (Typ.)

12V

1.8A / 115VAC         0.8A / 230VAC         0.7A / 277VAC

15V~54V

2.1A / 115VAC         0.9A / 230VAC         0.8A / 277VAC

INRUSH CURRENT (Typ.)

COLD START 75A/230VAC

LEAKAGE CURRENT

<0.75mA / 277VAC

PROTECTION

OVER CURRENT            Note.4

95 ~ 108%

Protection type : Constant current limiting, recovers automatically after fault condition is removed

SHORT CIRCUIT

Constant current limiting, recovers automatically after fault condition is removed

OVER VOLTAGE  

59 ~ 65V

Protection type : Shut down o/p voltage with auto-recovery or re-power on to recovery

OVER TEMPERATURE

100°C±10°C(RTH2)

Protection type : Shut down o/p voltage, recovers automatically after temperature goes down

ENVIRONMENT

WORKING TEMP.

-40 ~ +70°C(Refer to "Derating Curve")

WORKING HUMIDITY

20 ~ 95% RH non-condensing

STORAGE TEMP., HUMIDITY

-40 ~ +80°C, 10 ~ 95% RH

TEMP. COEFFICIENT

±0.03%/°C(0 ~ 50°C)

VIBRATION

10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes

SAFETY&EMC

SAFETY STANDARDS       Note.7

UL8750, CSA C22.2 No. 250.0-08, EN61347-1, EN61347-2-13 independent IP65 or IP67, J61347-1, J61347-2-13 approved ; design refer to UL60950-1, TUV EN60950-1

WITHSTAND VOLTAGE

I/P-O/P:3.75KVAC     I/P-FG:2KVAC     O/P-FG:0.5KVAC

ISOLATION RESISTANCE

I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25°C/ 70% RH

EMC EMISSION

Compliance to EN55015, EN55022 (CISPR22) Class B, EN61000-3-2 Class C (≥50% load) ; EN61000-3-3

EMC IMMUNITY

Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, EN55024, light industry level (surge 4KV), criteria A

QTHERS

MTBF

192.2K hrs min.      MIL-HDBK-217F (25°C)

DIMENSION

228*68*38.8mm

PACKING

1.15Kg; 12pcs/14.8Kg/0.8CUFT

NOTE

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25°C of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance: includes set up tolerance, line regulation and load regulation.

4. Derating may be needed under low input voltages. Please check the static characteristics for more details.

5. Type A only.

6. Safety and EMC design refer to EN60598-1, CNS15233, GB7000.1, FCC part18.

7. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time.

8. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.

9. Refer to warranty statement.