1 line wifi ip phone

1 line wifi ip phone

1 Introduction

1.1 Thanks for Purchasing

Thank you for purchasing SK601.The SK601 which has one line is a full-featured VOIP (Voice

over Internet protocol) phone that provides voice communication over IP network.

This phone functions not only much like a traditional phone, allowing to place and receive calls

and enjoy other features that traditional phone has, but also it owns many data services which you

could not expect from traditional telephone.

The SK601 provides Power over Ethernet(PoE) and one Ethernet port for connecting another

device to the local area network.

This guide will help you easily use the various features and services available on your phone.

1.2 Package Contents

Your Package includes the following:

One SK601(withPoE) IP Phone Unit

Handset and handset cord

One universal power adapter

One Ethernet cable

 Wall-mounting screw pack

If the above device or accessory is damaged or lost, please contact with your reseller for

replacement.

2 Installing

2.1Assembling the Phone and Connecting to the Network

1) Plug one end of the coiled phone cord into the left of the phone base.

2) Plug the other end of the handset cord into the jack at the button of the handset.

3) If you are using an external power source, push the power cord into the power supply, and plug

the power supply into the phone base unit. Then you will see the LED at the back of the phone

turns red.

Note: Use only the power supply that came with the phone.

4) Plug the Ethernet cable into Internet port in the rear side of the base station. Plug the other end

of the Ethernet cable into your already prepared network connection.

2.2Mounting the Phone to theWall

1) Complete the assembly introductions.

2) Attach two appropriate screws to the wall. Leave 1/4 distance from the wall. This allows you to

slide the mounting brackets on to the screws. Push down slightly to lock the phone in place.

2.3 Turning on the phone

This section assumes that the correct connections have been made.

1) Check whether the Internet port is well connected.

2) Plug the AC power adapter into the electrical outlet.

Note: Use only the adapter that comes with the phone.

3) Then the LED at the back of the phone will turn red, wait about 30 seconds, then the LED turns

green for a little while and turns light red again,hook and you can hear ring tone, that means you

can use the phone normally.

Note: If the LED does not turn on or you can not hear ring tone, re-confirm installation and

connections. If these are incorrect, try unplugging the phone and plugging it back in again. If you

still don’t have the upon features, then contact your Phone Administrator or service provider.

3 Get familiar

3.1 Front Panel

Front Panel NO. Part Name Description

1

Handset top

cradle

For the placement of handset(Receiver

end).

Hook switch For hang-up and hang-off of handset.

Cradle latch

To

prevent the handset from dropping

when it is wall-mounted.

Handset

bottom cradle

For the placement of handset(Transmitter

end)

Handset cord

port

RJ-11 jack on the left side of the IP phone.

Headset wire

port

RJ-11 jack on the bottom of the handset.

Headset

To

mount mouthpiece and earpiece on the

single handle.

2 Multi-Functi

onal Keys

These keys can be used as speed dial and

shortcut keys.

3 Numeric

Keypad

Enters numeric digits for initiating a call

or for entering configuration information.

4 HOLD The hold key is used to hold the current

call, press it again to release the hold

function.

5 XFER The XFER key is used to transfer calls,

including attended transfer and unattended

transfer.

6 CONF The CONF key is used to implement

conference meeting calls.

7 SPEAKER Press it to use handsfree.

3.2 Rear Panel

Rear Panel Part

Name

Description

DND

Switch

The switch is used to turn on or off DND.

Under the character DND is a dot. When

the switch near the dot, DND is on,

otherwise DND is off.

LED indicator, details please refer to

3.3LED Introduction.

DC 5V Power port

Internet Connects to the Ethernet switch, router or

Internet.

3.3 LED Introduction

LED

Indicator

Color Status Description

Light red Solid sk 601 is power on and not registered.

Green Solid sk601 is registered and line has no call.

Red Blinking There is a new call incoming.

Red Solid sk601 is registered and line is in active call.

Red Blinking in 10Hz sk601 is firmware upgrading.

1 line wifi ip phone                                                                                                                                                     1 line wifi ip phone