The Aggregate Crusher For Sale For Sale

Specifications

The Aggregate Crusher For Sale For Sale crushing action is carried out intermittently. This crusher due to simple structure, reliable and able to crush hard materials, etc. are widely used in mineral processing, building materials, silicate and ceramic industries. Adjusting device: The device is used to adjust the size of the nesting population size, control jaw crusher discharge size. I plant jaw crusher adjustment mechanism has two forms: mention long wedge and mandrel type gaskets, flexible and easy to adjust, to achieve stepless adjustment of The Aggregate Crusher For Sale For Sale

The main parts of jaw crusher is fixed body frame, chassis manufacturing process, there are two: carbon steel casting of carbon steel welded steel frame and chassis. Welded frame is in the original cast of the rack on the addition of a number of ribs Jaw crusher before starting bearing lubrication should be carefully examined the situation is good, whether the bearing bracket junction has enough grease Jaw crusher pre-start checks whether the ore crushing cavity or other debris should be removed immediately if

Features

The Aggregate Crusher For Sale For Sale Long Service Life, Large Feeding Size, Operate Easily, Less Noise, Low Cost Spare Parts,

The Aggregate Crusher For Sale For Sale Operation Notes:

Cut off operations and emergency stop processing 1, ore crusher All cut off must be ruled out before stopping. 2, cut off should be the first stop to the mining system (ie trough feeder). 3, vacuum cleaners and water system before stopping after 5 minutes. 4, the following conditions should an emergency stop: (1) The main shaft bearings or moving the jaw abrupt temperature exceed 80 ℃, the surface phenomenon is touching the back of the bearing can not be sustained for a second time. (2) before or after the thrust plate fracture. (3) belt loose bolts or other transmission parts likely to break when flying wounding. (4) Motor smoke "sweep bore."

Maintenance & Attention

Jaw crusher maintenance focuses rack chassis is the foundation since broken jaw, and only stable foundation in order to protect a broken jaw safe and efficient operation. According to Tian Rong machine broken jaw after-sales service for many years of experience, we believe that broken jaw rack routine maintenance parts that require special attention is not much, but the site operator must attach great importance. Usually broken jaw rack problems are caused by related parts, specifically summed up includes the following aspects: ① severe beating rack jaw broken, loose or broken bolt: tight bolt or replace broken bolts; ② fly counterweight sheave position deviation: Remove the fly sheave shaft cover plate, unscrew the fly, Lunzhang sleeve slot bolts, alignment fly counterweight sheave block position, and then sets up tight tight bolts; ③ host foundation is not solid, no isolation measures: jaw crusher reinforced base, padded sleepers or rubber, etc; ④ jaw broken rear of the chassis to produce percussion, rod not tightened, toggle plate and moving jaw hit the bracket to adjust the seat cushion: fastening rod; ⑤ lever and move the lower jaw hooks friction: a mechanical device to check whether the failure of the spring tension, such as failure of the replacement spring, adapter rod or retightening spring; ⑥ mutual impact between the spring and spring seat: the spring seat in place and tight tie rod nuts to the proper position.

To Choose a Right The Aggregate Crusher For Sale For Sale

Composite hammer, while having a higher life, but its casting and heat treatment process is complex. For this reason, in recent years developed a variety of low-alloy steel hammer, there 40CrMnSiMoRe been promoting low-alloy steel hammer. 40CrMnSiMoRe steel alloying elements, low production cost, simple process, you can get the required mechanical strength through the appropriate heat treatment. After analysis of the health of the hammer and experiments on the crusher, confirming the performance indicators in line with the kind of material hammer, hammer can be used as a good material. On the plant hammer crusher, 40CrMnSiMoRe high manganese steel hammer and hammer were worn compared. Test Method is mounted on the two rows of hammer crusher, each mounted in a row, with the machine running, test results: 40CrMn-SiMoRe hammerhead run 21d, the high manganese steel hammer run 14d, due to the two hammerhead wear different lengths, so use to measure the actual length of the wear life of more practical.