180W 7.5a single output power supply for led 24V

Item No.

CQ-24W-24V

CQ-36W-24V 

CQ-60W-24V 

CQ-100W-24V 

CQ-120W-24V 

CQ-150W-24V 

Output 

DC Voltage 

24V 

 24V

24V 

24V 

 24V

24V 

Rated Current 

1A

1.5A 

2.5A 

4.1A 

5A 

6.2A

Current Range 

0~1A 

0~1.5A 

0~2.5A 

0~4.1A 

0~5A 

0~6.2A

Rated Power 

24W 

36W 

60W 

 100W

120W 

150W 

Ripple & Noise (Max) Note 2 

150mVp-p 

 150mVp-p 

150mVp-p 

150mVP-p 

150mVp-p 

150mVp-p 

Voltage Tolerance Note 3

±5%

±5.0% 

Line Regulation 

±0.5%

±0.2% 

±0.5% 

±0.2% 

±0.6% 

±0.5% 

Load Regulation 

±0.2% 

±0.5% 

±0.5% 

 ±0.2%

±0.6%

±1.0 %

Set up time,Hold time

  200ms, 800ms,1000ms,50ms,20ms at full load

 Input

 Voltage Range Note. 4

90~250VAC;100~250VAC  vary by switch

Frequency Range 

47~63Hz 

 Efficiency (Type.)

86% 

88% 

86% 

85% 

87% 

86% 

 AC Current (Type.)

3.15A/115VAC 1.5A/230VAC 

 Inrush Current (Max)

Leakage Current 

<3.5mA / 240 VAC 

Protection 

Over Load 

105 ~ 150% rated output power 

Protection short circuit shut down o/p voltage, re-power on to recover

Over Voltage 

5.75~6.75V 

5.75~6.75V

27.6~32.4V

27.6 ~ 32.40V 

 21.6~26.4V

27.6v ~ 32.40V 

Protection type: Shut down o/p voltage, re-power on to recover 

Environment 

Working Temperature 

-30 ~ 70°c 

Working Humidity 

20 ~ 90% RH non-condensing 

Storage temp & Humidity 

-40~+80°c,10~95%RH 

Temp. coefficient 

±0.03/ºc (0~50°c) 

Vibration 

10 ~ 500Hz,2G 10min/1cycle,period for 60min,each along X,Y,Z axes 

Safety and EMC 

 Safety Standards

IP42 approved 

Withstand Voltage 

I/P-O/P,I/P-FG,O/P-FG:100M Ohms/500vdc

Isolation Resistance 

I/P-O/P,I/P-FG:100M OHMS/500VDC

EMC Emission 

Compilance to EN61000-4-2,3,4,5,6,8,11,ENV50204,EN55024,light industry level, criteria A

EMC Immunity 

Comply with EN55022 class B, EN61000-3-2 class A (≤80% load), EN 61000-3-3 

Others

MTBF 

703Khrs min, MIL-HDBK-217F (25ºC) 

Remark:

1.All technical data if not mentioned, it should be measured at 230v,rated load and 25 °c of relative temperature

2.Ripple and noise are tested at 20mhz of bandwidth via 12" twitsted pair-wire terminated with 0.1uf and 47uf parael cap.

3.Tolerance:set up tolerance,line regulation and load regulation are included

4.derating may be loaded with low input voltage, it should double check the detailed static characteristics

5.As power supply need to connected with final terminal equipment, which require the equipment to comply with EMC standard on the complete installation process again