Waste Water Treatment Bar Screen

Specifications

2,Install overloading safety protection device in the output shaft end of speed reducer , avoid damage equipment ude to accidental reasons overloading.

3,Due to bar screen rotary chain match with several rake tooth, with high remove dirt efficiency , thorough clean dirt.

4,Compact structure,simple electric control, convenient to realize automation.

Working principle:

GSHP type rotary rake type bar screen is main composed of driven device,rack,main axis,grid bar ,scum plate,rake tooth and driven chain; in the motor driven, after reduce speed by reducer, take chain wheel and chain motion, fix to the rotary chain, rake chain move to bottom after bar screen, after guide wheel turn over to bar front toward water level position, go on moving insert into mix bar space ascending, the intercept dirt in front bar lifting to water level, with chain move to slag outlet auto reverse, the dirt will auto discharge to conveyor or scum tank below bar screen, finish remove dirt process, liquid will flow by bar space, whole working procedure continuous proceed.

Technical data:

Installation and debugging instructions

 1). grille decontamination machine in hookon before installation should check the embedded steel location, size if it meets requirements, should guarantee;
A, grille Wells with two side should be vertical plane, well grille its perpendicularity tolerance weight may not exceed 20mm.

B, grille Wells should be parallel, both sides does not exceed the parallelism 20mm.
C, belt anchor foot two embedded steel plate should be and grille Wells plane surface flat top platform.

2). as the machine without making the depth, grille provide ditch decontamination machine into the groove, calibration Angle, the grille bearings after, based on the floor on side and grille ready, its frame welding installation Angle must comply with the design requirements, ensure the installation of an envisagement gear rake spent less 

than 1/1000mm, then tighten the anchor nut (if no embedded steel plate, usable expansion bolt).

3). discharge area safety cover, relax when tight sprocket, remove reducer end chain, electricity commissioning, see whether the steering gear reducer with safety cover as shown on the shoulder is consistent, forbidden to reverse direction.
4). use tensioner sprocket, adjust the chain firmness with tensioner screw adjusting rake the tooth chain firmness.

5). check reducer lube oil noodles line, whether to insufficient JiXieYou added to with size 46 oil noodles line. (equipment first operation shall first charging 46 # oil to decelerate oil a line)

(the machine has added  oil, replaced once a year)

6). pack on safety cover, the switch on the power no-load running, there shall be no jitter, jam and abnormal noise, no-load experiment, then input load operation operation.

5 .Common breakdown and elimination method:

1) in normal operation appears in motor running gear surface not running rake.
Fault reason: overloading and cause overload safety pin was cut off.

Elimination method:
(1) will be replace overload safety cover safety pin;
(2) found out by overloading reason, main look to whether sundry stuck rake chain;
(3) if there is sundry stuck rake chain, remove sundry rear can boot;
(4) rake in the chain chain attrib wattle wear with, must be replaced chain plank.

Replacing steps:

(1) the two root with iron stick will rake tooth chain stuck.
(2) use card spring clamps will have to replace chain chain of batten harrow tooth kadar discharge reed.
(3) will be two root rake tooth pulled pin shaft chain to replace new chain, then put the pin shaft strips in turn the card inserted, reed mount.
(4) installed hole plate can overhaul.
Three, routine maintenance and maintenance
(1) in the operation process, such as fibre beneficent bars around in sundry etc, should be clear in time, lest affect the normal operation of the machine.
(2) in normal operation, machine every two months, must use butter gun in all lubricating parts of the nozzle calcium grease Once injection

1.Long history , companying with good reputation

2. Good quality control system , Huge financial resources invested, Management System Systematized, and service personalized, which will be our goal and persistent forever. 

3. Huge market overseas . Our machines have been sold all over the world . especially Africa, Europe, Asia, and North America. Clients over many countries like Australia, Sri Lanka, UK, America, Mexico, Peru, Brazil, Kenya, Tanzania, Saudi Arab, UAE, etc.

4.Equipment working site , You are welcomed to visit our factory, the machines can be operated on site, and you will master the usage of machines nearby.

5. After-sales:

(1) 24 hours we are ready to explain question for you.

(2) Professional engineers supported, along with strong technical service.

(3) Excellent after-sales service.

(4) Any problem can be solved without influence products schedule of customers.