RS 100W 15V 7A AC-DC smaller size Switching Power Supply

MODEL

RS-100-15

OUTPUT

DC VOLTAGE

15V

RATED CURRENT

7A

CURRENT RANGE

0 ~ 7A

RATED POWER

105W

RIPPLE & NOISE (max.) Note.2

120mVp-p

VOLTAGE ADJ. RANGE

14.25 ~ 16.5V

VOLTAGE TOLERANCE Note.3

±1.0%

LINE REGULATION        Note.4

±0.5%

LOAD REGULATION Note.5

±0.5%

SETUP, RISE TIME

500ms, 20ms/230VAC  1200ms, 30ms/115VAC at full load

HOLD TIME (Typ.)

100ms/230VAC    18ms/115VAC at full load

INPUT

VOLTAGE RANGE

88 ~ 264VAC       125 ~ 373VDC (Withstand 300VAC surge for 5sec. Without damage)

FREQUENCY RANGE

47 ~ 63Hz

EFFICIENCY (Typ.)

82% 

AC CURRENT (Typ.)

2.5A/115VAC       1.5A/230VAC

INRUSH CURRENT (Typ.)

COLD START 40A/230VAC

LEAKAGE CURRENT

<2mA / 240VAC

PROTECTION

OVER LOAD

110 ~ 150% rated output power

Protection type : Hiccup mode, recovers automatically after fault condition is removed

OVER VOLTAGE

17.25 ~ 20.25V      

Protection type : Hiccup mode, recovers automatically after fault condition is removed

ENVIRONMENT

WORKING TEMP.

-25 ~ +70 °C (Refer to output load derating curve)

WORKING HUMIDITY

20 ~ 90% RH non-condensing

STORAGE TEMP., HUMIDITY

-40 ~ +85 °C, 10 ~ 95% RH

TEMP. COEFFICIENT

±0.03%/°C (0 ~ 50°C )

VIBRATION

10 ~ 500Hz, 5G 10min./1cycle, period for 60min. each along X, Y, Z axes

SAFETY &

EMC

(Note 6)

SAFETY STANDARDS

UL60950-1, TUV EN60950-1 Approved

WITHSTAND VOLTAGE

I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC

ISOLATION RESISTANCE

I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC

EMI CONDUCTION & RADIATION

Compliance to EN55022 (CISPR22) Class B

HARMONIC CURRENT

Compliance to EN61000-3-2,-3

EMS IMMUNITY

Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN61000-6-2 (EN50082-2) heavy industry level, criteria A

OTHERS

MTBF

260.8Khrs min. MIL-HDBK-217F (25 °C)

DIMENSION

159*97*38mm (L*W*H)

PACKING

0.6Kg; 24pcs/15.4Kg/0.7CUFT

NOTE

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 °C of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. Line regulation is measured from low line to high line at rated load.

5. Load regulation is measured from 0% to 100% rated load.

6. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets

EMC directives.

7. Length of set up time is measured at cold first start. Turning ON/OFF the power supply very quickly may lead to increase of the set up time.