cnc kit motors and drivers 220V M2280A, cnc power supply

REF

Peak

SW8

SW9

SW10

3.2A

4.5A

ON

ON

ON

3.5A

5.0A

OFF

ON

ON

3.9A

5.5A

ON

OFF

ON

4.2A

6.0A

OFF

OFF

ON

4.6A

6.5A

ON

ON

OFF

4.9A

7.0A

  OFF

ON

OFF

5.3A

7.5A

ON

OFF

OFF

5.7A

8.0A

OFF

OFF

OFF

Pulse/REV

SW1

SW2

SW3

SW4

SW5

200

ON

ON

ON

ON

ON

400

ON

ON

ON

ON

OFF

500

ON

ON

ON

OFF

ON

600

ON

ON

ON

OFF

OFF

800

ON

ON

OFF

ON

ON

1000

ON

ON

OFF

ON

OFF

1200

ON

ON

OFF

OFF

ON

1600

ON

ON

OFF

OFF

OFF

2000

ON

OFF

ON

ON

ON

2400

ON

OFF

ON

ON

OFF

2500

ON

OFF

ON

OFF

ON

3000

ON

OFF

ON

OFF

OFF

7200

OFF

ON

ON

OFF

ON

8000

OFF

ON

ON

OFF

OFF

10000

OFF

ON

OFF

ON

ON

12000

OFF

ON

OFF

ON

OFF

12800

OFF

ON

OFF

OFF

ON

20000

OFF

ON

OFF

OFF

OFF

24000

OFF

OFF

ON

ON

ON

30000

OFF

OFF

ON

ON

OFF

40000

OFF

OFF

ON

OFF

ON

60000

OFF

OFF

ON

OFF

OFF

TEST

OFF

OFF

OFF

OFF

OFF

Driver function

Operating instructions

Output

current

setting

Users can set the driver output current by SW8-SW10 three switches. The setting of the specific output current, please refer to the instructions of the driver panel figure.

Microstep setting

Users can set the driver Microstep by the SW1-SW5 five switches. The setting of the specific Microstep subdivision, please refer to the instructions of the driver panel figure.

Single/double

Pulse setting

SW7 sets pulse mode, setting “on” as double pulse mode, setting “off” as pulse + direction mode.

Self-test  setting

When SW1-SW5 five switches are all on “off”, the driver will test the motor normal or not according to the inner 1KHZ pulse.

Automatic half

current function

Users can set the driver half flow function by SW6. "OFF" indicates the quiescent current is set to half of the dynamic current, that is to say, 0.5 seconds after the cessation of the pulse, current reduce to about half automatically. "ON" indicates the quiescent current and the dynamic current are the same. User can set SW6 to "OFF", in order to reduce motor and driver heating and improve reliability.

Signal interfaces

PUL+ and PUL- are the positive and negative side of control pulse signal; DIR+ and DIR- are the positive and negative side of direction signal; ENA+ and ENA- are the positive and negative side of enable signal.

Motor interfaces

A+ and A- are connected to a phase winding of motor; B+ and B- are connected to another phase winding of motor. If you need to backward, one of the phase windings can be reversed.

Power interfaces

It uses AC power supply. Recommended operating voltage is 110VAC-220VAC, and power consumption should be greater than 500W.

Indicator lights

There are two indicator lights. Power indicator is green. When the driver power on, the green light will always be lit. Fault indicator is red, when there is over-voltage or over-current fault, the red light will always be lit; after the driver fault is cleared, if re-power the red light will be off.

Installation

instructions

Driver dimensions:198×76×130mm, please refer to dimensions diagram. Please leave 10CM space for heat dissipation. During installation, it should be close to the metal cabinet for heat dissipation.